Sealey WORKSAFE SSP11E.V2 Instructions Manual

Also see for WORKSAFE SSP11E.V2: Manual

BROW GUARD AND FULL FACE SHIELDMODEL NO: SSP11E.V2, SSP11ER.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 This face shield is designed for face and eye protection against high speed particles of low energy impact. The visor is designed tobe lightweight and comfortable to wear.9 The product protects against high speed particles worn over standard ophthalmic spectacles, but may transmit impacts, thus creatinga hazard to the wearer.9 Avoid liquids as small particles can splash into the eyes.9 Inspect the face shield frequently as a pitted or scratched face shield reduces vision and should be replaced immediately.9 When necessary, use identical replacement parts contact your Sealey stockist.8 DO NOT use if any part of the face shield is cracked or broken.8 DO NOT place this product on a hot surface.8 DO NOT use this face shield for protection against short circuit electric spark, fine dust, gas, ultra violet or infra red radiation,ionising radiation, liquids under pressure or other severe hazards.8 DO NOT use this face shield against heavy impact hazards.8 DO NOT use this face shield for welding.2. INTRODUCTIONRatchet adjustable headband with brushed nylon comfort band. Suitable for automotive, agricultural and industrial applications. Conforms toEN 166, Optical class 1, impact grade B.3. SPECIFICATIONModel No: ............................................................SSP11E.V2ConsumablesReplacement visor ............................................ SSP11ER.V2Lens Type: ..................................................................... clear4. ASSEMBLYRefer to picture overleaf4.1. Locate central hole of visor onto the central spigot of brow guard and lock in place by rotating the spigot.4.1.1. Gently fold the visor around the lip of the brow guard such that its’ outer slots align with outer spigots on brow guard. Lock inplace by rotating the spigots.4.1.2. Carefully remove the plastic protective sheet from the faces of the visor.4.2. FITTING VISORNOTE: It is imperative that the brow guard fits well and comfortably for the user or else slippage and discomfort may arise.4.2.1. Initially adjust height adjustment band to suit head size by un-clipping/adjusting the band.4.2.2. Use thumbscrew on the rear of the head band to make fine adjustment of circumference of the head band.4.2.3. To adjust the angle of the face mask with respect to the brow guard, use the thumbscrews on either side of the brow guard to set theangle. Tighten in position when adjusted accordingly.5. CLEANING & DISINFECTION8 DO NOT USE abrasive materials.5.1. Using a soft and clean brush or cloth, use warm suds to wash and clean. Ensure hands are clean (without grease).5.2. Materials which may come into contact with the wearer’s skin could cause allergic reactions to susceptible individuals. The contactareas should be disinfected regularly.6. MAINTENANCE6.1. The visor should be periodically inspected and cleaned to keep it clear. In case damage or damage to the visor, please replace.6.2. Ensure a correctly specified lens is fitted as a replacement (refer to Specification section). Ensure hands are clean (without grease)while fitting the lens.SSP11E.V2, SSP11ER.V2 Issue 1 03/11/20Original Language Version© Jack Sealey LimitedRefer toinstructions

/ 2

Related manuals for Sealey WORKSAFE SSP11E.V2