Menu
Sealey STW290.V2 Instructions Manual
  |
instructions fortorque adaptor digital 1/2”sq. drive40-200Nm (29.5-147.5lb.ft)model no: stW290.v2thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. safety WarNiNg! do Not use the digital torque adaptor if damaged or thought to be faulty.9 ensure all workshop safety rules, regulations and conditions are complied with when using this digital torque adaptor.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the working area.9 After use clean with a soft dry cloth and store in a safe, dry, childproof location.9 Keep the digital torque adaptor away from magnets.8 do Not subject the digital torque adaptor to excessive force or shocks.8 do Not drop or throw the digital torque adaptor.8 do Not use digital torque adaptor unless you have been instructed in its use by a qualified person.8 do Not leave the digital torque adaptor in any place exposed to excessive heat, humidity or direct sunlight.8 do Not use organic solvents such as alcohol or thinners to clean the digital torque adaptor.8 do Not submerge the digital torque adapter in water or any other liquid.8 do Not disassemble the digital torque adaptor.8 do Not exceed the permitted torque value for the digital torque adaptor.9 To ensure accurate measurement periodic re-calibration is necessary.2. iNtroductioNdesigned for use with a ratchet or breaker bar. Ideal for work around the engine bay and the tightening of wheel nuts to factory specifications.Large LCD display with selectable readings in Nm, lb.ft, lb.in, kg-cm or kg-m and accurate to ±2% of stated capacity. Memory stores up to50 readings and features auto shut off after 70 seconds. Supplied with certificate and storage case.3. specificatioNmodel no: ................................................................. STW290drive type: .................................................................. 1/2”Sq.length: ......................................................................... 75mmrange: ........................................ 40-200Nm (29.5-147.5lb.ft)Battery: ....................................................... 2 x AAA supplied4. operatioN WarNiNg! do Not press Mem and On/off buttontogether as this will enter the unit into calibration mode.4.1. poWer oN (fig.1).4.1.1. Attach the adaptor to a ratchet or breaker bar.4.1.2. After 2 seconds the LCD panel will show 0.0.4.1.3. tighten the nut or bolt.4.1.4. the lcd displays the torque value measured.Note: If not used for 70 seconds the Digital Torque Adaptor willautomatically shut off.4.2. HoW to select uNit (fig.1).Press mem and Peak / trace button together and release toselect different torque units.note: When you change units the target setting will also bechanged to the new units value.this digital torque Adaptor contains 5 unit selections.(kg-cm, kg-m, in-lb, ft-lb, N-m).4.3. HoW to select target torque value (fig.1).4.3.1. Increase (+): Press and hold the (+) button to increase thecurrent target value.sTW290.V2 | Issue:1 31/01/18Original Language Version© Jack sealey limitedrefer toinstructionmanualWear eyeprotectionfig.1 |
Related manuals for Sealey STW290.V2
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved