Sealey SSP201K Instructions Manual

1. SAFETYThe SSP201K system comprises a lightweight mask connected viaa breathing hose to a pre-set regulator, with spare carbon filter,mounted on a comfortable waist belt with quick release buckle. Thehose kit consists of a compressed air supply hose and couplings,fitted with a “Y” piece which connects to the pre-set regulator. A 1.5metre compressed air supply hose is provided for connection of aspray gun. A wall-mounted coalescing filter is supplied in the kit.SSP201 Comprises mask and waist belt only2. INTRODUCTION3. SPECIFICATIONThe SSP201 is the Full Face Mask and Belt assembly only, which must be used in conjunction with coalescing filter SSP21X and lowtoxic breathing hose SSP20H to provide clean air. The SSP201K is the complete air-fed full face mask system (see parts list). All furtherreferences relate to the SSP201K complete kit.1.1. General The SSP201K Complete Air Kit system is NOT designed for use in atmospheres containing flammable gas mixtures. The SSP201K is designed for use against contaminants which are NOT immediately dangerous to life and health or whereself-contained breathing apparatus is not essential. SSP201K is designed for use with COMPRESSED AIR ONLY. DO NOT USE WITH COMPRESSED OXYGEN OR OXYGENENRICHED AIR. No protection is given unless the mask is correctly fitted and an adequate supply of breathing air is maintained. Only when the equipment is correctly worn, will it provide the prescribed degree of protection. The SSP201K is the correct apparatus for persons with a beard or facial hair. DO NOT use a half mask. A combination of wall mounted filter SSP21X and belt mounted carbon filter unit WILL NOT remove Carbon Monoxide, CarbonDioxide, or other toxic gases. Wall mounted filter SSP21X is designed to remove particulate and moisture from the air supply. If you are in any doubt as to the suitability of the equipment for the work to be undertaken, consult your supplier.1.2. Negative Pressure At high work rates air pressure within the mask may become negative (a vacuum) briefly as the user breathes in. The apparatus has a maximum flow of 232 ltr/min and MUST NOT be used where work rate will require a supply in excess of232 ltr/min.1.3. Compressed Air Supply The user MUST ensure that the air supply to the apparatus is within the limits recommended. The air supply should be dry to avoid therisk of freezing in cold conditions. If the air supply ceases, or is reduced significantly, withdraw from contaminated atmosphere immediately and check system for faults.INSTRUCTIONS FOR:COMPLETE AIR FED BREATHING SYSTEMMODEL NO: SSP201K, SSP201(Mask & Belt Only)IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCTCORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILLINVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.Refer toInstructionsSSP201Air fed mask and belt filter for Model No. SSP201K. Light durable mask with specially shaped visor to reduce glare and reflection providing a widefield of vision. Waist belt assembly with a fixed flow control and an easy to change carbon deodorizing element.SSP201KA full kit of equipment manufactured to provide a protection factor of APF40. Primarily for use in automotive spray shops but also suitable for usein none critical dust and fume applications. Allows user to safely perform all the tasks of cutting, grinding and spraying. Includes complete head setwhich has wide vision, is easily adjustable and has a built in audible alert for low airflow. Waist belt assembly with a fixed flow control and easy tochange carbon deodorizing element. Supplied with 10mtr low toxic hose with 1.5mtr leader hose and a complete set of couplings. Adheres to thefollowing standards EN14594 class 3A, EN166 and EN12021Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSP201KOperating Pressure: . . . . . . . . . . . . . . . . 30-100psi (2-7bar)Maximum Pressure: . . . . . . . . . . . . . . . . . . . . . 116psi (8bar)Air Flow: . . . . . . . . . . . . . . . . . . .150-180ltr/min (5.4-6.4cfm)Maximum Operating Temperature: . . . . . . . . . . . . . . . . 35°CUK Protection Factor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Hose Diameter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mmMain Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mtrLeader Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . 1.5mthrOriginal Language Version SSP201K,SSP201 Issue: 1 - 09/01/15© Jack Sealey Limited

/ 3

Related manuals for Sealey SSP201