Sealey SPB57T Instruction Manual

InstructIon MAnuAL for:BROADCAST SPREADER 57kg TOWBEHINDMoDEL no: SPB57Tthank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONSIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.3. SPECIFICATION & CONTENTS2. INTRODUCTION4.1. check contents against fig.1 above, if anything is missing ordamaged contact your local sealey dealer.4.2. refering to fig.2, place an axle bush (18) onto the axle of theframe tube assembly(1).4.3. Attach the pneumatic wheel (5) then a Ø16 flat washer (17) tothe mounting tube axle. secure with split pin (11) and repeatprocedure for the other side. Additional Ø16 flat washers (17) areprovided to adjust the spacing between the axle bushing (18)and the pneumatic wheel (5).4.4. rotate one pneumatic wheel (5) so that the hole on the inside ofthe wheel boss aligns with the corresponding hole in the axletube. Insert inner hex bolt M5x45 (10) through the axle tube andsecure with lock nut M5 (12) as shown in figure 2.4. ASSEMBLYModel No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPB57Tcapacity (Weight). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57kgcapacity (Volume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60ltrspread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3.6mtrWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6kgDimensions (W x D x H). . . . . . . . . . . . . . . . . . .680 x 980 x 790mm Ensure that the spreader is in sound condition and good workingorder before use. Ensure that the operator is fully trained and competent to operatethe prime mover before attaching and using the spreader. Ensure that all chemical safety instructions are adhered to whenhandling products for use in the spreader. A full range of personalsafety equipment is available from your sealey dealer. Always distribute the load evenly. Ensure all non essential personnel keep a safe distance when thespreader is in use. replace or repair damaged parts. Use only recommended parts.Unauthorised parts may be dangerous and will invalidate thewarranty. Keep hands and feet away from moving parts. DO NOT overload the spreader - see specification. DO NOT leave unattended, especially when loaded, unless thewheels are chocked or the spreader is otherwise secured. DO NOT allow others to ride on the spreader. DO NOT allow untrained personnel to use the spreader. DO NOT use the spreader for purposes other than for which it isdesigned. DO NOT operate the spreader when you are tired or under theinfluence of alcohol, drugs or intoxicating medicines. When loaded,DO NOT operate the spreader over edges, roughsurfaces etc. where the spreader is at risk of overturning. WARNING! failure to comply with these instructions may resultin damage to spreader or other property and/or personal injury.Manufactured with a strong tubular steel frame and polypropylenedispensing hopper. Pin hitch design attaches to ride-on lawnmowers,can be converted to ball hitch using Model no. tB36. fitted withaluminium gear, rain cover, pneumatic tyres and adjustable feedsystem. Includes hopper screen to ease spreader flow and filter outunwanted contaminants. sprays in 360° motion to cover a large area.suitable for a variety of horticultural agents, including grit, seed, salt,fertiliser and weed killer.Original Language Version sPB57t Issue: 1 - 21/06/11fig.1fig.2

/ 4

Related manuals for Sealey SPB57T