Sealey SD200 Instructions Manual

Also see for SD200: Instructions

instructions forinstant heat soldering gunmodel no: sd200thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. saFetY1.1. electrical saFetY Warning! it is the user’s responsibility to check the following:check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and allelectrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electricalproducts. You may obtain an rcd by contacting your local sealey dealer.if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliancetest) tested.electrical safety information: it is important that the following information is read and understood.1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correctfuse - see fuse rating in these instructions.8 do not pull or carry the appliance by the power cable.8 do not pull the plug from the socket by the cable.8 do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired orreplaced immediately by a qualified electrician.1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.if the cable or plug is damaged during use, switch the electricity supply and remove from use.Ensure that repairs are carried out by a qualified electrician.Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.B) Connect the BROWN live wire to the live terminal ‘L’.C) Connect the BLUE neutral wire to the neutral terminal ‘N’.ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.Sealey recommend that repairs are carried out by a qualified electrician.if an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted ispreferred since any appliance plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but tobe absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets,we recommend the use of 2.5mm² section cable. if an extension reel is to be used outdoors, ensure it is marked for outdoor use.1.2. general saFetY Warning! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment.9 Familiarise yourself with the application , limitations and potential hazards of the soldering iron/gun.9 replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.9 locate soldering iron/gun in a suitable working area, keep area clean and tidy and free from unrelated materials.9 Keep the work area clean, uncluttered and ensure there is adequate lighting.9 Keep the soldering iron/gun clean for best and safest performance.9 ensure there are no flammable or combustible materials near the work area.9 Wear approved safety eye protection (standard spectacles are not adequate).9 Wear appropriate protective clothing.9 Ensure the workpiece is adequately held before operating the soldering iron/gun.9 Always lay the soldering gun on its side so that the tip cannot make contact with the work surface.9 remove excess solder from the soldering gun by wiping the tip on a damp, natural sponge.9 ensure that when the soldering gun is put down during use that the tip is not near to or in contact with any material that may burn or meltincluding the product’s own supply lead.8 do not attempt to remove excess solder from the soldering iron/gun by shaking it. Hot solder may become airborne and land on yourskin causing burns and blisters.8 do not allow children or pets into the area where the soldering is taking place.8 do not attempt to cool the gun with water.8 Warning! disconnect the soldering gun from the mains power and allow it to cool before changing tips.8 do not operate the soldering gun when you are tired or under the influence of alcohol, drugs or intoxicating medication.8 do not leave a hot soldering gun unattended.replacement fuserating: 3 aMPsD200 Issue 4 (H, F) 05/02/18Original Language Version© Jack sealey limitedrefer toinstructionmanualWear protectivegloves Wear eyeprotection

/ 2

Related manuals for Sealey SD200