Menu
Sealey SA96 Quick Start Manual
   |
AIR ENGRAVERMODEL NO: SA96Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when usingthis equipment. WARNING! Disconnect from air supply before changing engraving tips, or servicing ,or performing any maintenance.9 Maintain the engraver in good condition (use an authorised service agent).9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.9 Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.9 Before each use check condition of engraving tip. Sharpen if necessary. If worn or damaged replace immediately.9 Ensure there are no flammable or combustible materials near the work area. WARNING! Always wear approved eye (or face) and hand protection when operating the engraver.9 Use face, dust, or respiratory protection in accordance with COSHH regulations.9 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.9 Wear appropriate protective clothing and keep hands and body clear of working parts.9 Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non-slip shoes.9 Keep children and unauthorised persons away from the working area.9 Check moving parts alignment on a regular basis.9 Ensure workpiece is secure before operating the engraver.9 Avoid unintentional starting. WARNING! Ensure correct air pressure is maintained and not exceeded. Max air pressure = 60PSI9 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connectionsare secure.9 Prolonged exposure to vibration from this equipment poses a health risk. It is the owner’s responsibility to correctly assess thepotential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.8 DO NOT use the engraver for a task it is not designed to perform.8 DO NOT operate the engraver if any parts are damaged or missing as this may cause failure and/or personal injury.8 DO NOT carry the engraver by the hose, or yank the hose from the air supply.8 DO NOT force, or apply heavy pressure to the engraver; let the tool do the work.8 DO NOT place air line attachments close to your face and do not point at other people or animals.8 DO NOT operate engraver when you are tired, under the influence of alcohol, drugs or intoxicating medication.8 DO NOT use engraver where there are flammable liquids, solids or gases such as paint solvents and including waste wiping orcleaning rags etc.8 DO NOT direct air from the air line at yourself or others. When not in use, disconnect from the air supply and store in a safe, dry,childproof location.2. INTRODUCTIONComposite bodied high quality tool with Tungsten Carbide tip for engraving metals and plastics. Suitable for security marking loan products,applying service date information to tools and for marking components prior to storage. Supplied with 1.5m of small-bore hosing and1/4”BSP adaptor.3. SPECIFICATIONModel no: ...................................................................... SA96Air inlet size: .............................................................1/4”BSPConsumable parts: .............................SA96/03 - Tungsten tipFree speed: ............................................................. 3000spmNoise power/pressure: ......................................... 84/73dB(A)Operating pressure: ...................................................... 60psiVibration/Uncertainty: ....................................... 3.89/0.88m/s²Refer toinstructionmanualWear eyeprotection Wear earprotection Wear protectivegloves Wear a maskSA96 Issue:3 (H,F) 26/07/21Original Language Version© Jack Sealey Limited |
Related manuals for Sealey SA96
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved