Menu
Sealey CP1207 Quick Start Manual
Also see for CP1207: Quick start guide
  |
49PC 12V CORDLESS MULTI-PURPOSEROTARY TOOL & ENGRAVER KIT - BODYONLYMODEL NO: CP1207Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 Disconnect the battery from the tool before changing accessories, servicing or performing any maintenance.9 Maintain tool and accessories in good condition. Check moving parts and alignment. If necessary use an authorised service agent.9 Replace or repair damaged parts using recommended parts. Unauthorised parts may be dangerous and will invalidate the warranty.9 Wear approved safety eye protection with side shields and a dust mask if generating dust.9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.9 Use the tool in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.9 Maintain correct balance and footing.9 Keep children and unauthorised persons away from the work area.9 Secure unstable work piece with a clamp, vice or other adequate holding device.9 Avoid unintentional starting. Keep the tool clean for best and safest performance.9 When not in use switch tool off. Store it in the case and put in a dry, childproof area.8 DO NOT over-reach. Ensure the floor is not slippery and wear non-slip shoes.8 DO NOT use the tool for a task it is not designed to perform.8 DO NOT operate tool where there are flammable liquids or gases.8 DO NOT get the tool wet or use in damp or wet locations.8 DO NOT hold unsecured work in your hand.8 DO NOT leave the tool running unattended.8 DO NOT operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.8 DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.2. i INTRODUCTIONCompact, lightweight cordless multipurpose rotary tool & engraver. Comfortable composite housing with soft grip to reduce vibration. Six speedsettings provide the control required to complete various tasks. Quick release collet and spindle lock for fast tool changes. Supplied with a full rangeof tips, wheels, sanding discs, dressing stones and a chuck spanner. Integral LED battery level indicator. Requires Model No. CP1200BP 12V 1.5AhLithium-ion Battery and Model No. CP1200MC Battery Charger.3. i SPECIFICATIONModel no ................................................................... CP1207Battery options12V 1.5Ah Li-ion, 12V 3Ah Li-ion, 12V 4Ah Li-ion (not included)Collets ................................................... 1, 1.5, 2, 2.4, 3.2mmConsumable partsCP1200BP - Battery 12V 1.5Ah,CP1200BP3 - Battery 12V 3Ah,CP1200BP4 - Battery 12V 4Ah (not included)Free speed .................................................... 5000-25000rpmNoise power/pressure .......................................... 74/63dB(A)Vibration/uncertainty ........................................ 1.024/1.5m/s²4. CONTENTSHSS Drill Bits (x6), Mandrel (x2), Polishing Disc (x3), Grinding Disc (x4), Metal Brush, Cutting Disc (x16), Collet Chuck (x5), Synthetic Brush(x2), Milling Bits (x2), Engraving Bits (x2), Grinding Bits (x5), Combination Spanner5. OPERATION5.1. FITTING ACCESSORIES5.1.1. Ensure the tool is switched off and the battery removed.5.1.2. Press the spindle lock button and slowly turn the collet nut until the spindle lock engages. Refer to fig.1.5.1.3. Retain pressure on the spindle lock button and turn the collet nut anticlockwise to open the collet (Spanner provided).NOTE: Never press the spindle lock button when the tool is running.5.1.4. The required accessory may now be fitted into the collet. Fully insert the accessory shaft to reduce the risk of bending in use.CP1207 Issue 2 (2) 11/05/20Original Language Version© Jack Sealey LimitedRefer toinstructionmanualWear eyeprotection Wear facemask Wear protectiveglovesfig.1 |
Related manuals for Sealey CP1207
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved