Sealey SA55.V2 Instructions Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICHIT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATETHE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY INSTRUCTIONS WARNING! Ensure Health & Safety, local authority and general workshop practice regulationsare adhered to when using this equipment. WARNING! Disconnect from air supply before changing accessories or servicing. Maintain the tool in good condition and replace any damaged or worn parts. Usegenuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi. Keep air hose away from heat, oil and sharp edges. Check air hose for wear before eachuse and ensure that all connections are secure. Wear approved safety eye/face shield, ear defenders and hand protection. Keep fingers clear of blades. Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes. Keep children and non essential persons away from the working area. DO NOT use the tool for a task it is not designed to perform. WARNING! DO NOT use tool if damaged or thought to be faulty. Contact Sealey service agent. DO NOT use tool unless you have been instructed in its use by a qualified person. DO NOT carry the tool by the air hose, or yank the hose from the air supply. DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicatingmedication. DO NOT carry tool with your hand on the power trigger in order to avoid unintentional starting. DO NOT direct air from the air hose at yourself or others. When not in use disconnect from air supply and store in a safe, dry, childproof location. WARNING: The warnings, cautions and instructions discussed in this instruction manualcannot cover all possible conditions and situations that may occur. It must be understoodthat common sense and caution are factors which cannot be built into this product, but mustbe applied by the operator.INSTRUCTIONS FOR:AIR SCISSORSMODEL No: SA55.V22. INTRODUCTION & SPECIFICATIONMax. Cutting Capacity: 1.2mm(Steel) 1.5mm(Aluminium)Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . 4.3cfmOperating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . 90psiAir Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSPWeight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4kgReplacement Blade Left: . . . . . . . . . . . . . . .SA55.V2-34Replacement Cutter Right: . . . . . . . . . . . . . .SA55.V2-35Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 96.53dB(A)Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . 85.53dB(A)Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.78m/s²Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . 0.5868m/s²Polished aluminium housing with textured grip handle. Suitable for accurately cutting metal sheet.Unlike air shears this tool is ideal for trimming ragged sheet edges to gain a flat finish. Handleexhaust helps reduce noise level.Original Language Version SA55.V2 Issue: 2(SP) - 12/11/13© Jack Sealey Limited

/ 5

Related manuals for Sealey SA55.V2