Sealey Professional TOOLS AUTO SERVICE Series Instructions Manual

1.1. GENERAL SAFETY7 DO NOT use the bore scope if dropped and/or damaged7 DO NOT operate near live electrical wires.7 DO NOT operate near moving parts such as pulleys, motors,gears or fans etc.7 DO NOT bend the bore scope shaft tighter than 2.5 inch radius(5 inch diameter).7 DO NOT expose the bore scope housing to water or other liquids.7 DO NOT insert the bore scope shaft into locations whosetemperature is greater than 45°C. Maintain the bore scope in good and clean condition for best andsafest performance. A full range of personal safety equipment is available from yourSealey dealer. Wear suitable clothing to avoid snagging. Do not wear jewelleryand tie back long hair. Account for all tools and parts being used and do not leave anyin, or near, the engine. Be alert to your surrounding environment while using the borescope.Note the location of the object to be inspected and determine aroute to it. Bend the bore scope shaft to follow the route.1.2. MAINS POWER ELECTRICAL SAFETY (In relation to thebattery charger) WARNING! It is the owner’s responsibility to check thefollowing: You must check all electrical equipment andappliances to ensure they are safe before using. You mustinspect power supply leads, plugs and all electrical connectionsfor wear and damage. You must ensure that the risk of electricshock is minimised by the installation of appropriate safetydevices. An RCCB (Residual Current Circuit Breaker) should beincorporated in the main distribution board. We recommend thatan RCD (Residual Current Device) is used with all electricalproducts. It is particularly important to use an RCD with portableproducts that are plugged into a supply not protected by anRCCB. If in doubt consult a qualified electrician. You may obtainan RCD by contacting your dealer. You must also read andunderstand the following instructions concerning electrical safety.1.1.1. The Electricity At Work Act 1989 requires all portable electricalappliances, if used on business premises, to be tested by aqualified person, using a Portable Appliance Tester (PAT), atleast once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners ofelectrical appliances responsible for the safe condition of theappliance and the safety of the appliance operator. If in anydoubt about electrical safety, contact a qualified electrician.1.1.3. Ensure that the insulation on all cables and the product itself issafe before connecting to the mains power supply. See 1.3.1.above and use a Portable Appliance Tester (PAT).1.1.4. Ensure that cables are always protected against short circuit andoverload.1.1.5. Regularly inspect power supply leads, plugs and sockets for wear,damage or loose connections.1.1.6. Check that the voltage marked on the product is the same as thepower supply to be used and check that the plug is fitted with thecorrect capacity fuse.1.1.7. DO NOT pull or carry the appliance by attached leads.1.1.8. DO NOT pull plug from socket by the power cable.1.1.9. DO NOT use worn or damaged cables, plugs or connectors.Immediately have any faulty item repaired or replaced by aqualified electrician.Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT ISINTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THEWARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY INSTRUCTIONSINSTRUCTIONS FOR:VIDEO BORE SCOPE Ø6mm x 1000mmMODEL No: VS81952. INTRODUCTIONSuitable for internal inspection of cylinder head bores, enginecompartments and other machinery/industrial applications. Flexibleshaft diameter is small enough to fit through most spark/glow plug andinjector apertures. Features three tip mounted mirrors 30º , 45º and 60ºallowing a clear view in confined spaces. A magnetic attachment is alsoincluded. Capable of taking photos/videos which can be viewed on acomputer via the SD card. Ideal for warranty authorisation. Suppliedwith SD card, AV cable, battery charger and comprehensive instructionsin carry-case.3. SPECIFICATIONProbe Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6mmProbe Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mmMinimum Bend Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5”/64mmCamera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic exposureCamera viewing Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°Light source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x LEDsScreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5” LCD MonitorScreen resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 x 240 pixelsLCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ColourVideo Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTSC & PALBattery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7V RechargeableCharger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110V - 230V(LI)Flash memory storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 2GB SD CardCompression Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG4VS8195 Issue No:1 01/06/09fig.11.3. BATTERY CHARGER SAFETY INSTRUCTIONS WARNING! DO NOT attempt to charge any battery other thanthat supplied for the bore scope. Other types of batteries mayexplode! All mains electrical supply safety features must be followed asdescribed in Section 1.1. Disconnect the charger from the mains power supply when not inuse. DO NOT expose the charger to damp or wet conditions. DO NOT pull or carry the charger by the power lead. DO NOT operate the charger if it has been dropped, received asharp knock, or is damaged. Take charger to an authorised agent. DO NOT dismantle the charger as this may cause damage orpersonal injury and will invalidate your warranty.

/ 3

Related manuals for Sealey Professional TOOLS AUTO SERVICE Series