Sealey PWH1 Manual

Auto DArkening WelDing HelmetSHADe 9-13Model no: PWH1, PWH2, PWH3 and PWH4thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.imPortAnt: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAfety WArning! This helmet is not suitable for use with laser welding or CUTTInG or for overhead welding applications.9 ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The helmet will notoffer protection against misuse of workshop tools, equipment, or accessories.9 Maintain the helmet in good condition and protect cartridge from liquid and dirt contact. Regularly replace the protective lens andreplace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.9 ensure the front cover window is securely in place before use.9 Fit the helmet and adjust the head band so the helmet will sit as low and near to your face as possible.9 Use helmet only in temperatures ranging from -10°C to 60°C.9 Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.9 Maintain correct balance and footing.9 Ensure the floor is clear from obstructions, not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the working area. WArning! The helmet will only protect the eyes and face from radiation and sparks. It will not protect against explosive devices orcorrosive liquids.8 Do not use helmet for any purpose for which it is not designed.8 Do not use helmet unless you have been instructed in its use by a qualified person.8 Do not open or tamper with the shade cartridge.8 Do not get the helmet wet or use in damp or wet locations.8 Do not leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.8 Do not place the helmet on a hot surface.8 Do not use helmet without front cover window fitted. To do so will invalidate your warranty.9 Clean helmet (see section 5.4) and store the helmet in a safe, dry, childproof location. WArning! Before welding always inspect the cartridge filter to ensure that it is not damaged. To test the filter prior to welding,direct the front of the cartridge filter to a bright light source which will cause the lens to darken. Then using your hand rapidly coverand uncover the sensor. The filter should lighten momentarily then return to a dark state. WArning! Do not use the helmet if damaged or you suspect it may be faulty. (Contact Sealey stockist).▲ DAnger! Do not USe if, at any time, the face plate in the cartridge FAIlS to darken when exposed to a welding spark. Removecartridge and return to your Sealey stockist for checking.▲ DAnger! Continued use of the product knowing that the auto darkening feature is noT FUnCTIonInG may dAMAGe YoUReYeS and CAUSe BlIndneSS.2. introDuctionWelding helmet with infinitely adjustable shade control between 9-13. Complies with BS EN 379, BS EN 175 and DIN standards. Fullyautomatic switching from light to dark on striking arc. Shade is selected by a rotary knob on side of helmet. Grinding function enables user togrind without removing mask. Solar panel power supply - no batteries required. Features sensitivity and delay controls for switching light todark. Suitable for MIG, TIG, arc welding and grinding.3. SPecificAtionGrinding Function:........................................................................................... Yesoperating Temperature: .................................................................. -5°C to +55°Coperating Time light/dark: ..................................................................... “0.04ms“Power:.................................................................................................. Solar CellsShade Active: ................................................................................... 9-13 VariableShade Inactive: ................................................................................................... 4Viewing Area: .........................................................................................92x42mmPWH1, PWH2, PWH3, PWH4 Issue 1 17/06/19Original Language Version© Jack Sealey limitedRefer toinstructions

/ 4

Related manuals for Sealey PWH1