Menu
Sealey PT1170H.V3 Quick Start Manual
    |
fig.1LIFT PALLET TRUCK - 1000KG CAPACITYMODEL NO: PT1170H.V3Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY Only open bottomed Euro type pallets can be used with this truck8 DO NOT use a faulty or damaged truck. Before using the truck all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the wheels,handle and fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced beforethe truck is used. All repairs must be carried out by an authorised Sealey service agent. Personnel who operate the truck and those in the vicinity of operation should wear safety footwear with reinforced toe caps at all times.8 DO NOT allow persons other than the operator to stand in front of or behind the truck when it is moving, lifting or lowering. Never place any part of your body in the lifting mechanism or under the forks or load. DO NOT place a foot in front of a rolling wheel injurycould result.8 DO NOT allow others to ride on the truck.8 DO NOT lift or move unstable or loosely stacked loads. Take extra care when operating a loaded truck in high winds. Take special care when moving long, high or wide loads in order not to dislodge the load by striking any fixtures, vehicles or people in thearea of operation. Always ensure that the load is evenly distributed across the forkswith the centre of the load being at the halfway point of the length ofthe forks.8 DO NOT overload the truck - refer to the specification for maximumpermitted load. If a load is left unattended even for a very short period of time itshould be lowered to the ground. When not in use the truck should be left in the lowered position. Ensure that the width and length of the forks is correct for the palletto be lifted. Ensure that the truck is sufficiently inserted into the pallet to lift thefull width of the pallet. Use the truck on level, flat, hard surfaces and in well lit areas.8 DO NOT use truck on sloping or uneven ground; DO NOT attemptto negotiate curbs, steps or ramps. Be aware of differences in floorlevels.8 DO NOT use the truck in explosive atmospheres.8 DO NOT use the truck if you are unsure of the stability of the truck. The operator of the truck must be physically capable of controllingthe load selected; particularly in relation to stopping a rolling load.8 DO NOT modify the truck.2. INTRODUCTIONHeavy-duty high lift pallet truck suitable for the loading/unloadingof light commercial vehicles as well as warehouse/generalhandling duties. Features twin stabilisers for extra balance whenat maximum lift and an ergonomic handle design for comfortableoperation.3. SPECIFICATIONModel No: ...................................................PT1170H.V3Capacity: ............................................................. 1000kgFork Spread: ....................................................... 225mmForks (Length x Overall Width: .................1170 x 540mmMaximum Height: ................................................ 800mmMinimum Height: ................................................... 85mmRefer toinstructionmanualDO NOTreach inWear safetyfootwearDO NOT getunder truckDO NOT rideon truckOriginal Language Version© Jack Sealey Limited PT1170H.V3 Issue 3 15/08/23CONTENTS1 Chassis 4 Steering Wheel2 Tiller 5 Scissors3 Hydraulic Cylinder and Pump 6 Control LeverNumbers in brackets not applicable to this model |
Related manuals for Sealey PT1170H
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved