Sealey PC2100.V2 Instructions Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONSINSTRUCTIONS FOR:PRESSURE WASHERSModels: PC2100.V2 & PC2100PLUSIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1.1. ELECTRICAL SAFETYp WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any otherconnectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual CurrentDevice (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protectedby an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualifiedelectrician, using a Portable Appliance Tester (PAT), at least once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliancesand the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.and use a Portable Appliance Tester.1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check allconnections to ensure that none is loose.1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supplyto be used and that the plug is fitted with the correct fuse - see fuse rating at right.1.1.7. DO NOT pull or carry the appliance by the power cable.1.1.8. DO NOT pull the plug from the socket by the cable.1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faultyitem repaired or replaced by a qualified electrician. When an ASTA/BS approved UK3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.Fit a new plug according to the following instructions (UK only).a) Connect the GREEN/YELLOW earth wire to the earth terminal ëEí.b) Connect the BROWN live wire to the live terminal ëLí.c) Connect the BLUE neutral wire to the neutral terminal ëNí.d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulationextends beyond the cable restraint and that the restraint is tight.Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that asuitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any applianceplugged into it will be protected. The cable core section is important and should be at least 1.5mm2 , but to be absolutely sure that thecapacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of2.5mm2 section cable.FUSE RATING 13 AMPBlueNeutralWireYellow & GreenEarth WireCableRestraintBrownLiveWire1.2. GENERAL SAFETYp WARNING! Water and Electricity are dangerous partners. Be extremely cautious and always be aware that this device uses anelectric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.p WARNING! DO NOT USE the washer if any part of the unit, gun, nozzle, detergent bottle, hose or cables is damaged. Replace orrepair using genuine parts only. Non-authorised parts may be dangerous and will invalidate your warranty. Always check connectionsare correctly secured and not cracked or damaged in any way before using the machine.p WARNING! Use washer on a flat, levelled surface, in a horizontal position. Failure to do so willinvalidate your warranty. NEVER stand the washer on end during use.4 Ensue you comply with all local water supply regulations. Power washers may only be connected tomains drinking water supply if a back flow preventer valve is installed in the supply hose, or at the tap outlet.4 The supply hose must must be reinforced, and have an internal diameter of 1/2î. The water supplymust be at least equal to the cleaner capacity. The water temperature must NOT exceed122 O F (50 O C). The water supply pressure must NOT exceed 145psi (10 bar).4 Always be aware of the potential hazards that may occur during use. Study all applicationsand limitations of the washer before use.4 Use where air can freely circulate around the washer to avoid the machine over heating.4 Keep the washer in good condition. Use authorised service agent to service the unit.4 Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.4 Position the washer as near to the water supply as possible.p WARNING! Ensure all persons and animals keep at a minimum distance of16 yards (15m) from the nozzle when in use.p WARNING! The pressure washer must only be used with clean water. Unfiltered water or corrosive chemicals must not be used asthese will damage the cleaner.PC2100.V2 & PC2100PLUS - 1 - 180203

/ 4

Related manuals for Sealey PC2100.V2