Sealey PC2100 Instructions Manual

1.1. ELECTRICAL SAFETY. p WARNING! It is the users responsibility to read, understand and comply with the following:You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs andall electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safetydevices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that areplugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Deviceby contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested bya qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the applianceand the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains powersupply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply leads and plugs for wear and damage and all electrical connectionsto ensure that none is loose.1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supplyto be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may requirea fuse smaller than 13 amp for certain products (subject to 1.1.10. below) see fuse rating at right.1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.1.1.8. DO NOT pull power plugs from sockets by the power cable.1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired bya qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut offand fit a new plug according to the following instructions (discard old plug safely).(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.a) Connect the GREEN/YELLOW earth wire to the earth terminal E.b) Connect the BROWN live wire to live terminal L.c) Connect the BLUE neutral wire to the neutral terminal N.d) After wiring, check there are no bare wires, that all wires have been correctly connected, that the cable external insulationextends beyond the cable restraint and that the restraint is tight.Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked withthis symbol . To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue to the earth terminal.1.1.10. Some products require more than a 13 amp electrical supply. In such a case, NO plug will be fitted. You must contact a qualified electricianto ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and socket with your electrician.1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCDfitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores of the cableis important. 1.5mm 2 section cable is the minimum but to be absolutely sure that the capacity of the cable reel is suitable for thisproduct and for others that may be used in the other output sockets, we recommend the use of 2.5mm 2 section cable.Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONSINSTRUCTIONS FOR:P R E S S U R E WA S H E RModel : PC2100IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.BlueNeutralWireYellow & GreenEarth WireCableRestraintFUSE RATINGTHIS PRODUCT MUST BE FITTEDWITH A13 AMP FUSEBrownLiveWire1.2 GENERAL SAFETYp WARNING! Water and Electricity are dangerous partners. Be extremely cautious and always be aware that this device uses anelectric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.p WARNING! DO NOT USE the washer if any part of the unit, gun, nozzle, detergent bottle, hose or cables is damaged. Replace orrepair using genuine parts only. Non-authorised parts may be dangerous and will invalidate your warranty. Always check connectionsare correctly secured and not cracked or damaged in any way before using the machine.p WARNING! Use washer on a flat, levelled surface, in a horizontal position. Failure to do so willinvalidate your warranty. NEVER stand the washer on end during use.4 Ensue you comply with all local water supply regulations. Power washers may only be connected tomains drinking water supply if a back flow preventer valve is installed in the supply hose, or at the tap outlet.4 The supply hose must must be reinforced, and have an internal diameter of 1/2. The water supplymust be at least equal to the cleaner capacity. The water temperature must NOT exceed140 O F (50 O C). The water supply pressure must NOT exceed 145psi (10 bar).4 Always be aware of the potential hazards that may occur during use. Study all applicationsand limitations of the washer before use.4 Use where air can freely circulate around the washer to avoid the machine over heating.4 Keep the washer in good condition. Use authorised service agent to service the unit.4 Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.4 Position the washer as near to the water supply as possible.p WARNING! Ensure all persons and animals keep at a minimum distance of16 yards (15m) from the washer when in use.p WARNING! The pressure washer must only be used with clean water. Unfiltered water or corrosive chemicals must not be used asthese will damage the cleaner.PC2100 - 0061 - (2) - 050401

/ 4

Related manuals for Sealey PC2100