Sealey PBF04 Instructions Manual

INSTRUCTIONS FOR:FLOOR & BENCH MOUNTED METAL BENDERSMODEL NOS: PBF04 & PBB04Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.PBF04 & PBB04 - 1 - 1610031. SAFETY INSTRUCTIONSIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.3. ASSEMBLY & PREPARATION2. INTRODUCTION3 Ensure that the metal bender is in sound condition and goodworking order. Take action for immediate repair or replacement ofdamaged parts. Use recommended parts only. The use ofimproper parts may be dangerous and will invalidate the warranty.3 Keep bender and associated parts clean for best and safest performance.3 Locate the bender in a suitable, well lit work area.3 Keep work area clean and tidy and free from unrelated materials.3 Mount onto a strong, stable work surface or onto level and solidground (preferably concrete) as appropriate.3 Ensure all non-essential persons keep a safe distance whilst thebender is in use.3 Check that all bending dies, pins, stops and attachments are correctlyand securely mounted before commencing a bend.For light workshop use this compact metal bender comes in bench or floor mounted versions and is designed to bend flat, square or round solidhot rolled mild steel up to the dimensions given below. The bender comes with the following accessories. A stop block, stop block support,seven circular dies (1î,1.ºî,1.Ωî,1.æî,2î,2Ωî), a sharp angle bend attachment, extending handle, one short hinge pin, two long hinge pins, plusfixed and adjustable stops to aid repeat production of the same part.BENDING CAPACITY (around a circular die) : Flat material - up to 5/16î x 2î Square or round material - up to 5/8îBENDING CAPACITY (using the sharp angle attachment) : Use only flat mild steel 3/16î up to 2î wide or 1/4î up to 1 1/4îwide.DO NOT bend round stock using the sharp angle attachment)pp WARNING! Ensure that you have read and understood Section 1 Safety Instructions before operating the bender.pp WARNING! To avoid serious injury do not operate the bender unless it is securely mounted to the floor or workbench.3.1. Attach the ring/loop assembly to the floor stand or bench stand as indicated in fig.1.3.1.1 Attach the loop end first by placing the long spacer (1) into the loop. Place a flat washer (3) over the bolt (2) and insert the boltthrough the loop and long spacer. Insert the protruding bolt into the mounting plate at the top of the stand ensuring that there is ashort spacer (6) sandwiched between the loop and the mounting plate. Secure with a lock washer (7) and a nut (8).3.1.2 Attach the ring end to the stand in the two places indicated using the two 3/8î bolts with countersunk heads (5). Ensure that there is ashort spacer (6) inserted between the ring and the mounting plate through which each bolt passes. Place a flat washer and a lockwasher over each bolt and secure with a lock nut.3.2 Attach the handle to the ring/loop as indicated in fig.2.3.2.1 Insert the loop end of the handle inside the loop of the ring/loop assembly and secure it with one of the two longer hinge pins. Thehole selected on the handle loop will depend on the type of bend to be done. (See section 4)3.3 Extend the handle to its full length. (See fig.2)3.3.1 Remove the hair clip from the handle pin, then remove the pin from the handle. Pull the extension arm out of the handle tube andalign the hole at the end of the extension with the hole in the handle tube. Reinsert the pin and retain it by reinstalling the hairclip.3.4 Fix the assembled unit to the floor or bench as appropriate.3.4.1 Place the bender in the position where you intend to use it and rotate the handle fully in both directions to ensure that there will be noobstructions during bending. The bender must be attached to a bench or floor using fixings which are strong enough to resist theturning force exerted on them. Similarly the structure of the bench or floor surface must also besound and strong enough to resist the turning force exerted through the fixings.3 Wear safety goggles and gloves when bending parts.3 Always allow enough material to extend beyond the stop blockand forming dies when making bends to ensure that the materialdoes not come free allowing the handle to release suddenly.7 DO NOT bend any material other than hot rolled mild steel.7 DO NOT operate the metal bender if damaged.7 DO NOT allow untrained persons to operate the bender.7 DO NOT use the metal bender for purposes other than thatfor which it is intended.7 DO NOT try to bend round stock using the sharp angle attachment.7 DO NOT modify the bender in any way or use a handle extensionother than the one provided.7 DO NOT try to bend material larger than the maximum sizesstipulated below.fig.1fig.2

/ 3

Related manuals for Sealey PBB04