Sealey PH20 Instructions Manual

Your crane is delivered assembled but in a folded condition. Before use it is necessary to lay the folded crane on its back on the floor andproceed as follows:3.1. Raise the crane legs and lock them into place by passing the locking pins through the body. Retain with cotter pins.3.2. Lift the assembled crane onto wheels.3.3. Open release valve by turning to left and pump 10-20 times. This will flush the hydraulic system and purge any air that may be present.3.4. Pull crane jib up slightly, close valve and pump the handle. The jib will now raise. Pump the jib all the way up and then lower it (this willconfirm that the oil level is correct).3.5. Crane is now ready. Ensure it is complete and not damaged. If you experience any problems contact your supplier immediately.INSTRUCTIONS FOR: FOLDING CRANEModel: PH20Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONS3. ASSEMBLY INSTRUCTIONS2. SPECIFICATIONLifting capacity, Position 1: kg . . . 2000Lifting capacity, Position 2: kg . . .1500Lifting capacity, Position 3: kg . . .1000Lifting capacity, Position 4: kg . . . .500Length of jib, Position 1: mm . . . . .920Length of jib, Position 2: mm . . . .1100Length of jib, Position 3: mm . . . .1280Length of jib, Position 4: mm . . . .1460Max. lift @ min. jib extension: mm . . . . . . . . .1800Max. lift @ max. jib extension: mm . . . . . . . . .2055Height (max) of frame legs: mm . . . . . . . . . . . .185Length (max) of frame: mm . . . . . . . . . . . . . .1652Width (max) of frame legs: mm . . . . . . . . . . . .1175Overall height: mm . . . . . . . . . . . . . . . . . . . . .1630Width (max) inside frame legs: mm . . . . . . . .1030Distance between rear wheel centres: mm . . . .445Weight: kg . . . . . . . . . . . . . . . . . . . . . . . . . . . .104IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.4. OPERATING INSTRUCTIONSp WARNING! Before using the crane ensure that you have read and understood Section 1 safety instructions and that 3.3 and3.4 have been successfully completed.4.1. Close the release valve at base of ram by turning valve tap clockwise.4.2. Put the handle into the pump socket and pump. The jib will then move - continue to pump until the jib reaches the required height.4.3. Connect the crane hook to the load using a suitable certified sling or support beam. Ensure that you are aware of the load weightand have checked that it is within the capacity of the crane at the jib extension you are using. When removing engines ensure youknow the weight you are lifting and use only lifting points recommended by the vehicle manufacturer.4.4. Lift only directly above the load. p WARNING! DO NOT LIFT THE LOAD AT AN ANGLE.PH20 - 0016 - (2) - 2408013 Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as describedin Section 5. Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all accessory lifting devicesare suitably certified. If crane is damaged, immediately remove from service.3 Ensure the surface on which the crane is used is level and firm, being capable of sustaining the crane and the maximum load.7 NEVER use crane on tarmacadam or other soft surfaces.3 Ensure the crane legs and arms are locked before use and jib extension is locked in fixed jib position by means of the lock pin.3 Keep children and unauthorised persons away from the work area.3 Keep work area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.3 Ensure that load does not exceed the maximum lifting capacity. Overloading the crane is dangerous. Where appropriate, use onlythe lifting points recommended by the manufacturer of the load to be lifted.3 Before lifting the load ensure that the crane jib is in the lowest possible position, that there are no obstacles which may snag the load whilstbeing lifted and that the area above the jib is clear.7 Do not apply any sideways pressure to the crane during lifting or suspension of load.3 To avoid injury, be fully aware of your own and other persons locations in relation to the lifting and lowering of the load.3 Keep a sound footing and balance, wear non-slip shoes and ensure that the floor is not slippery.3 Ensure the centre of gravity always remains inside the crane base.7 Do not harness the load at an angle and do not allow the load to swing during lifting.7 Do not allow load to drop suddenly. Lower load with care and be fully aware of the condition of the surface onto which load is to be lowered.7 Do not operate the hydraulic power unit beyond its maximum stroke as indicated on the label.7 Do not load beyond rated capacity for each specified jib position as indicated in Section 2. The capacity of crane reduces as jib is extended.7 Do not position any part of your body beneath the load and do not climb on the crane.7 Do not use the crane to move or transport a load around the workshop. The crane is a lifting device only.7 Do not attempt to adjust the safety valve, which has been set and sealed by the manufacturer.7 Do not use the crane to perform a task for which it is not designed.7 Do not use whilst under the influence of drugs, alcohol or intoxicating medication.3 When not in use, store the crane in a safe, dry, childproof area.p WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the warranty.2 Ton folding crane - economymodel. Fast folding for easystorage and transportation. Heavyduty castors. Weighs only 104kgand is perfect for mobile orworkshop use. Pump accessfrom side.

/ 3

Related manuals for Sealey PH20