Sealey MLB80MB Instructions Manual

12/24V 120W SMD LED MINI LIGHT BAR -MAGNETIC BASE, SINGLE POINT FIXINGMODEL NO: MLB80MB, MLB80SBThank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 Familiarise yourself with this product’s application and limitations, as well as any specific potential hazards peculiar to the beacon.9 Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate thewarranty.8 DO NOT use the beacon for any purpose other than for which it is designed.8 DO NOT allow children to operate the beacon.8 DO NOT operate the beacon if any parts are missing or damaged as this may cause failure or possible personal injury.9 When not in use switch the beacon off and where appropriate remove plug from power supply.2. INTRODUCTIONMLB80MBExtremely bright 120W amber LED high intensity mini light bar fitted with a high strength magnet strong enough to cope with normalroad speeds and ease of installation. 10 Modules fitted with 8 LEDs allowing a 360° light. Fitted with a 3mtr cable and cigarettelighter power plug. Plug includes 2 switches, on/off and a momentary switch, giving you the option of 9 different flash patterns.Built-in memory recalls last pattern selected. ECE R65 & R10 Approved for highway use. CE Approved and E-Marked. IP56 rated.MLB80SBExtremely bright 120W amber SMD LED high intensity mini light bar fitted with a 10mm single bolt fixing. 10 Modules fitted with 8 LEDs,creating a 360° light. Built-in 10 option flash pattern that has a built-in memory which recalls the last pattern selected. ECE R65 & R10Approved for highway use. CE Approved and E-Marked. IP56 rated.3. SPECIFICATIONModel No: ............................................MLB80MB, MLB80SBDimensions: ................. 279mm (w) x 61mm (h) x 165mm (d)Supply: ................................................................. 12-24V DCTemperature Range: ...................................... -30°C to +50°C4. OPERATION4.1. WIRING4.1.1. Black wire should be wired to a suitable earth.4.1.2. Red wire should be wired via a switch to a suitable fused 12Vlive supply fitted with a 5 amp fuse.4.1.3. Yellow wire should be wired to earth via a momentaryswitch (negative earth).4.2. ATTACHING THE LIGHT TO YOUR VEHICLE4.2.1. There are two strong magnets on the reverse of the unit.(fig.1)4.3. ATTACHING THE LIGHT BAR VIA THE SCREW FITTING4.3.1. The screw can be removed from the underside of the lightbar by removing the fixing plate. (fig.1)4.3.2. Under the fixing plate there is a recess for the head ofthe setscrew to sit in. This will stop the setscrew fromturning when tightening the nut. (fig.2)4.4. SWITCHING ON AND CHANGING THE LIGHTPATTERN4.4.1. There are two buttons on the in car adaptor. One switch(with LED indicator light) switches the light on and off.The other switch switches light patterns. (fig.3)MLB80MB, MLB80SB Issue 2 (4) 28/07/22Original Language Version© Jack Sealey LimitedRefer ToInstructionsfig.1fig.2Warning! Do NotLook Directly IntoLight.Warning! HotSurfaces

/ 2

Related manuals for Sealey MLB80MB