Sealey HVD24.V2 Instructions Manual

Also see for HVD24.V2: Instructions

InstructIons For:industrial high velocity fansmodel no's: hvd24.v2, hvd30.v2, hvd36.v21. safety instructions1.1. electrical safety Warning! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any otherconnectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. Aresidual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual currentdevice (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protectedby an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.you must also read and understand the following instructions concerning electrical safety.1.1.1. the electricity at Work act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualifiedelectrician, using a Portable Appliance tester (PAt), at least once a year.1.1.2. the health & safety at Work act 1974 makes owners of electrical appliances responsiblefor the safe condition of those appliances and the safety of the appliance operators. if inany doubt about electrical safety, contact a qualified electrician.1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting itto the power supply. see 1.1.1. and 1.1.2. and use a Portable Appliance tester.1.1.4. ensure that cables are always protected against short circuit and overload.1.1.5. regularly inspect power supply cables and plugs for wear or damage and check allconnections to ensure that none is loose.1.1.6. important: ensure that the voltage marked on the appliance matches the power supplyto be used and that the plug is fitted with the correct fuse - see fuse rating at right.1.1.7. do not pull or carry the appliance by the power cable.1.1.8. do not pull the plug from the socket by the cable.1.1.9. do not use worn or damaged cables, plugs or connectors. Immediately have any faultyitem repaired or replaced by a qualified electrician. When an AstA/Bs approved uK 3 pin plug is damaged, cut the cable just abovethe plug and dispose of the plug safely.Fit a new plug according to the following instructions (uK only).a) connect the green/yelloW earth wire to the earth terminal ‘e’.b) connect the BroWn live wire to the live terminal ‘l’.c) connect the Blue neutral wire to the neutral terminal ‘n’.d) after wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outerinsulation extends beyond the cable restraint and that the restraint is tight.double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.to rewire, connect the wires as indicated above - do not connect either wire to the earth terminal.1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensurethat a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socketwith your electrician.1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any applianceplugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure thatthe capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend theuse of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.recoMMended fuse ratinghvd24.v.2 3aMP,hvd30.v2 & hvd36.v2 5aMP.1.2. general safety disconnect the fan from the mains power when not in use and before servicing or performing any maintenance. use the fan in dry areas only. do not use in wet or areas with high condensation such as showers, pools etc. Warning! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. do not touch thefan until the mains power supply has been disconnected. Always disconnect the fan from the power supply when moving it from one location to another and ensure fan is stood on a level surface. the fan air flow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air. Keep the fan clean and maintained in good condition. For motor service contact an authorised service agent. use recommended parts only. unapproved parts may be dangerous, and will invalidate your warranty. do not operate the fan where there are explosive or flammable gases, fumes or other hazardous substances. do not stand the fan on the power cable. do not insert any objects through the fan guard. do not cover the fan when in use. do not immerse the fan in water or any other liquid. do not allow children to operate the fan. do not stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip. do not use the fan outdoors. do not modify speed control or attempt to fit any additional external speed control device to the fan. When not in use place the fan in its original box, or otherwise cover, to protect from dust and store in a safe, dry, childprooflocation.note: this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilitiesor lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance bya person responsible for their safety. children should be supervised to ensure that they do not play with the appliance.© Jack sealey limitedIMPORTANT: Please read these instructions carefully. note the safe oPerational reQuireMents, Warnings & cautions. use theProduct correctly and With care for the PurPose for Which it is intended. failure to do so May cause daMage and/orPersonal inJury and Will invalidate the Warranty. KeeP these instructions safe for future use.thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.HVd24.V2, HVd30.V2 & HVd36.V2 Issue: 3 (l) - 21/03/14Original Language Version

/ 2

Related manuals for Sealey HVD24.V2