Sealey HBS971 Instructions Manual

Also see for HBS97.V2: Manual

HBS97.V2, HBS971 - 2 - 2908063. WORKING SURFACE3. 1. Position the vehicle on the designated headlamp aim standing area.3. 2. When positioning the HBS ensure the floor is perfectly even and level.3. 3. If this is not possible the vehicle and HBS must be on the same slope, which must not exceed 0.5∫.3. 4. Headlights must not be checked where surfaces exceed 0.5∫ angle. (See fig 3A.).OKfig 3A. NO NO0.5 0 MAXINSTRUCTIONS FOR:UNIVERSAL HEADLAMP BEAM SETTERMODELS:H B S 9 7 . V 2 & H B S 9 7 1Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.4. 1. Straighten vehicle wheels.4. 2. Check the tyre pressure.4. 3. Ensure the headlights are clean and dry.4. 4. If the vehicle is fitted with manual or electric headlamp levelling devices, ensure these are set up for vehicle with normal load.4. 5. Remove anything which could alter the vehicles position, i.e. Snow, Ice, Mud, etc.4. VEHICLE PREPARATIONIMPORTANTPLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.The SEALEY HEADLAMP BEAM SETTERS, HBS97.V2 & HBS971 are supplied with a rotating column, mirror and visor. The HBS97.V2 hasthe addition of a rail set. Either HEADLAMP BEAM SETTER may be used for checking headlights on cars, motorcycles and commercial vehicles.The HBS97.V2 is approved by VOSA for testing all vehicle classes with the appropriate set of rails (Excluding HGV).SPECIFICATIONS: Height . . . . . . . .1520/1770mm Maximum height of beam measurement . . . . . . .1410mmWidth . . . . . . . . . . . . . .610mm Minimum height of beam measurement . . . . . . . . 240mmLength . . . . . . . . . . . . .610mm Focal Length . . . . . . . . . . . . . . . . . . . . . . . . . . . .500mmA BASEB COLUMNC VERTICAL SLIDING SYSTEMD MIRROR-VISORE OPTICAL SYSTEMF COLUMN LOCK PEDAL2. 0 Place large metal washer over spigot at base of column B.2. 1 Insert column spigot into bearing in base A and retain with socket cap bolt andwasher provided.2. 2. Attach mirror-visor D to the rotating metal friction plate at the top of the columnusing the two socket cap bolts provided.2. 3. Fit the optical system E to the vertical - sliding system using an M8 bolt in both thetop and bottom holes.2. 4 If the unit is to run on rails these need to be fixed to the floor of the test bay withlow profile fixings that will not interfere with the movement of the wheels.2. 5 To ascertain the correct positions for the rails place a typical vehicle in the test bayand follow the test procedure without rails. When the unit is correctly positioned forone headlamp mark the wheel positions on the floor including a longitudinalcentre line. Roll the unit over to the other headlamp, check the alignment, andmark the floor again.2. 6 Place the rails loose on the floor using the markings made and put the unit onthem. Roll the unit from one lamp to the other and recheck the alignment. Whensatisfied that all is correct fix the rails to the floor.2.7 HBS97.V2 is approved by VOSA for class I,II,III and IV as delivered, and bypurchasing HBS97E Rail Extensions the unit is also suitable for Class V, VI,VII.For testing classes I, II, III and IV the rails may be surface mounted. Werecommend the rails be recessed into the floor for all other vehicle testing classes.1. DESCRIPTION2. ASSEMBLING THE BEAM SETTERGENERAL RULES. Read instruction manual carefully before using the headlight beam tester.TO AVOID DAMAGE ENSURE THE FOLLOWING IS STRICTLY APPLIED.DO NOT allow unqualified persons to operate this device.DO NOT use this device in direct sunlight.DO NOT splash the unit with water or any other liquid.DO ensure the work area is well ventilated.DO ensure that there is good lightingDO put the handbrake on.DO avoid sudden changes in temperature.DO avoid sudden vibration.

/ 4

Related manuals for Sealey HBS97.V2