Sealey BT2020.V2 Instruction Manual

Also see for BT2020: Instruction manual Quick start guide

BATTERY MONITOR SENSOR & VEHICLEFINDERMODEL NO: BT2020.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY▲▲ DANGER! BE AWARE , LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION .FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, WHILST CONNECTING THISPRODUCT TO A VEHICLE’S BATTERY.9 Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intendto use in the vicinity of the battery. Remember to review warning marks on all products and on engines. WARNING ! Modern vehicles contain extensive electronic systems.9 You are required to check with the vehicle manufacturer, for any specific instructions regarding the use of this type of equipment oneach vehicle.NOTE: No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.2. INTRODUCTIONDisplays real time battery power, voltage and temperature. Wireless connection with dedicated app which supports up to 4 devices (IOS &Android compatible). Guide user back to the vehicle by automatically recording the last parking location. Record the route, cost and drivinghabits of each trip, which can be exported to Excel. Automatically monitor the starting and charging system of the vehicle and notify ifabnormal. Compatible with most batteries including lead sealed, AGM and Gel. Supports up to 4 devices. Store historical data in device for upto 30 days.3. SPECIFICATIONMODEL NO.: ....................................................... BT2020.V2Voltage Range: ............................................................ 6-20VAverage Current: ......................................................... 1.5mAInput Voltage: .............................................................. 6-20VVoltage Accuracy: .......................................... (9-16V) ±0.03VOperating Temperature: .................................... -20°C - 40°CWaterproof: .................................................................... IP67Short Circuit Protection: ............................................. Built InReverse Connection Protection: ................................. Built InPhysical Dimensions: ................................ 55 x 41 x 12.5mm4. OPERATIONNOTE: The input voltage range of the device is 6V-20V, which is suitable for 12V lead-acid batteries. Too high input voltage willcause equipment damage.NOTE: In order to obtain accurate battery temperature, please stick the device on the battery case.NOTE: When installing the app, all permissions to be obtained must be accessed. If a permission fails to be obtained, somefunctions cannot operate.NOTE: Some functions need to allow the app to self-start and run in the background. The app has been optimized for this and willnot consume more power. To allow the app to start automatically and run in the background, Allow Background, Allow Self Startingand Auto-Launch needs to be set in the phone. Consult your phone’s instructions for guidance.4.1. INSTALLING THE DEVICE4.1.1. Connect the positive tab (red lead) to the positive terminal on the battery. Connect the negative tab (black lead) to the negativeterminal on the battery. When removing the device, disconnect the negative terminal before the positive.4.1.2. Fix the device to the battery case with the supplied double - sided tape.The device must be attached to the battery case, otherwise the accurate battery temperature will not be obtained. Be careful not tochoose a ventilated location, which will affect the battery temperature reading.4.2. INSTALLING THE APP4.2.1. Scan the QR code of the product and download the app to your device.4.2.2. When running the application for the first time, the app will ask for required permissions, all these are necessary (see note above).NOTE: The Android app obtains the location permission for the wireless scanning function, which is regulated by the Android system.BT2020.V2 Issue 2 (1) 14/04/23Original Language Version© Jack Sealey LimitedRefer toinstructions * Electricalshock hazard* Wear eyeprotection* Wearprotective gloves* Wear safetyfootwear* Wearprotectiveclothing* ONLY FOR WORKINGNEAR BATTERY

/ 2

Related manuals for Sealey BT2020