Sealey AK7064 Quick Start Manual

ELECTRICAL SAFETY. WARNING! It is the owner’s responsibility to read, understand and comply as follows:You must check all electrical equipment and appliances to ensure they are safe before using.You must inspect power supply leads, plugs and all electrical connections for wear and damage.You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. AnRCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We alsorecommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly importantto use an RCD together with portable products that are plugged into an electrical supply not protected by anRCCB. If in doubt consult a professional electrician. You may obtain a Residual Current Device by contactingyour Sealey dealer.You must also read and understand the following instructions concerning electrical safety.1.1.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to betested by a qualified electrician at least once a year by using a Portable Appliance Tester (PAT).1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe conditionof the appliance, and the safety of the appliance operator. If in doubt about electrical safety, contact a qualifiedelectrician.1.1.3 Ensure the insulation on all cables and the product itself is safe before connecting to the mains powersupply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).1.1.4 Ensure that cables are always protected against short circuit and overload.1.1.5 Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especiallypower connections, to ensure that none are loose.1.1.6 Important: Ensure the voltage marked on the product is the same as the electrical power supply to be used, andthat plugs are fitted with the correct capacity fuse.1.1.7 DO NOT pull or carry the powered appliance by its power supply lead.1.1.8 DO NOT pull power plugs from sockets by the power cable.1.1.9 DO NOT use worn or damaged leads, plugs or connections.Immediately replace or have repaired by a qualified electrician.A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,cut off and fit a new plug according to the following instructions(discard old plug safely). (UK only - see diagram at right).Ensure the unit is correctly earthed via a three-pin plug.a) Connect the green/yellow earth wire to the earth terminal ‘E’.b) Connect the brown live wire to live terminal ‘L’.c) Connect the blue neutral wire to the neutral terminal ‘N’.After wiring, check there are no bare wires, that all wires have been correctlyconnected and that the wire restraint is tight. Double insulated products areoften fitted with live(BROWN) and neutral (BLUE) wiresonly. Double insulated products are always marked with this symbol .Check you model carefully to see which type of product your have. To re-wirea double insulated item connect the brown and blue wires as indicated above.DO NOT connect brown or blue to the earth terminal.1.1.10 Cable extension reels. When a cable extension reel is used it should be fullyunwound before connection. A cable reel with an RCD fitted is recommendedsince any product which is plugged into the cable reel will be protected. The section of the cable on the cablereel is important. This should be at least 1.5mm² section cable but to be absolutely sure that the capacity of thecable reel is suitable for this product and for others that may be used in the other output sockets, we recommendthe use of 2.5mm² section cable.1. SAFETY INSTRUCTIONSYellow & GreenEarth WireFUSE RATINGTHIS PRODUCT MUSTBE FITTED WITH A:13 AMP FUSEBrownLiveWireBlueNeutralWireWireRestraintINSTRUCTIONS fOR:ELECTRIC NAILER15-32MMmODEL: AK7064Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions andproperly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONALREQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THEPURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.Original Language Version AK7064 Issue: 2 - 23/10/09

/ 3

Related manuals for Sealey AK7064