Sealey ADT7.V2 Quick Start Manual

ADJUSTABLE GEARBOX SUPPORT 500KGCAPACITY SUITABLE FOR MODELS 300ETJ.V2AND 500ETJ.V2MODEL NO: ADT7.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY WARNING! Ensure all preliminary checks are carefully carried out before using gearbox support and transmission jack. WARNING! Follow all of the safety instructions issued with the transmission jack. WARNING! Ensure load is placed level and centrally on gearbox support and is fixed in place before attempting to lift, lower, ortransport load. Always use load restraint chains and attachments to stabilise and secure the load to the gearbox support.9 Before use ensure the transmission weight and size DO NOT exceed the capacity of the gearbox support or the transmission jack.9 The gearbox support is heavy, care should be taken when placing onto the transmission jack.9 Ensure that the sliding bracket and chain mount bracket nuts and bolts are fully tightened when the gearbox support is loaded.9 Care should be taken when using the gearbox support and vertical transmission jack in conjunction with a vehicle lift to ensure that thevehicle is not lowered whilst the jack is in position.9 Before storing ensure gearbox support is clean and free of grease and oil.9 Store in a safe, dry childproof location.8 DO NOT use the gearbox support without restraint chains.8 DO NOT replace the chains with an inferior form of restraint.8 DO NOT allow untrained persons to use the gearbox support.8 DO NOT move the transmission jack, with or without a load, with the gearbox support in the raised position.8 DO NOT use the gearbox support for any purpose other than for vehicle transmissions.2. iINTRODUCTIONFully adjustable saddle with forward, backward and side to side tilt. Suitable for use with Model Nos: 300ETJ.V2 and 500ETJ.V2.3. iSPECIFICATIONModel No:.................................................................ADT7.V2Capacity: ...................................................................... 500kgCompatibility: .................................... 300ETJ.V2, 500ETJ.V2Net weight ................................................................. 12.02kg4. ASSEMBLY WARNING! Failure to assemble the gearbox support correctly may result in serious damage and/or personal injury. Unpackthe product and check contents against the contents list. Should there be any damaged or missing parts contact your supplierimmediately.4.1. ASSEMBLY (refer to fig.1)4.1.1. Position the support plate (2) on a flat surface with the bracket facing upwards. Place the main support (1) over the support plate (2) sothat the bracket fits into the slot on the main support (1).Refer toinstructionmanualWear protectivegloves Wear protectiveclothingWear safetyfootwearItem Description Qty Item Description Qty1 Main Support 01 10 Flat Washer 062 Support Plate 01 11 Spring Washer 103 Adjuster Screw 02 12 M10 Nut 104 Pivot Pin 01 13 Circlip 025 Sliding Bracket 02 14 Split Pin 016 Chain Mount Bracket 04 15 Chain 027 M8 Bolt and Nut 02 16 Retaining Bolt 028 Chain Hook 02 17 Reduction sleeve 019 M10 x 30mm Bolt 06fig.1ADT7.V2 Issue 3 (H, F) 07/09/18Original Language Version© Jack Sealey Limited

/ 2

Related manuals for Sealey ADT7.V2