Sanyo SEC-MDU012AAN Operating Instructions Manual

Also see for NC-MDU01: Operating instructions

AA/AAA USB Charger Ni-MHOperating InstructionsThank you for purchasing this SANYO product. For safeand correct use, please read these instructions carefully.Please keep the instructions for later reference.Model: NC-MDU01SpecificationsSpecificationsSANYO Model No. NC-MDU01SANYO Model No. NC-MDU01Input DC 5 V, max. 500 mAInput DC 5 V, max. 500 mAOutput DC 1.2 V, 850 mA x 1 (Quick), 450 mA x 2Output DC 1.2 V, 850 mA x 1 (Quick), 450 mA x 2Battery charge times(approx. minutes)*eneloop Ni-MH AA (typ. 2000 mAh)1 pc. 140 min, 2 pcs. 280 mineneloop Ni-MH AAA (typ. 800 mAh)1 pc. 60 min, 2 pcs. 120 min(*) Guideline value only; actual charging times may vary slightly. Please referto Operating Instructions.Dimensions (L x W x H) 93 x 47 x 17.5 mmDimensions (L x W x H) 93 x 47 x 17.5 mmWeight Approx. 47 gCharging temperaturerange 0 °C – 40 °CConnector type USB type ACompatible computermodelsModels with a USB port as standard equipmentwhere the computer manufacturer guaranteesthe operation of the USB port and has a USBport fitted as Standard equipment.Discharging (battery use) -5 °C – 50 °CDischarging (battery use) -5 °C – 50 °CCharging 0 °C – 40 °CStorage -20 °C – 30 °CUsage outside of these temperature ranges may decrease the performanceand/or the life of the battery.Temperature rangeFeatures• This is a small and slim eneloop charger for AA and AAAeneloop batteries.• One or two AA or AAA eneloop batteries can be charged.• No AC adapter is required.HOW TO INSERT THE BATTERYDepending on whether the adjuster is raised or not, one ortwo AA or AAA batteries can be charged.PARTS DESCRIPTIONOperating InstructionsOperating InstructionsHOW TO CHARGE1. Insert one or two eneloop batteries into the charger. Raise or lowerthe adjuster depending on the type of battery to be charged.• Raise the adjuster to charge AA batteries.• Lower the adjuster to charge AAA batteries.• AA and AAA batteries cannot be charged at the same time.Note: Insert the batteries matching the polarity of the charger.2. Insert the USB connector of the charger into the USB port of anoperating computer. Charging takes place when the LED chargeIndicator is flashing.Note: Do not connect other equipment to other USB ports on thecomputer while charging or the required Power may be exceeded.Charging might be stopped or the computer damaged or Data lost.The power supply capacity may be exceeded and charging maybecome impossible or the computer may be damaged and importantdata may be lost.3. When charging has been completed the LED Charge indicatorremains lit. Remove the USB connector from the USB port of thecomputer and remove the battery (batteries).• Directly after completion of charging, the battery is hot, but thisis normal.Note: If the adjuster has been raised, lower the adjuster for storage.Cautions for Battery Charger UsageCautions for Battery Charger UsageWARNING!The following can be considered when the charge time is exceeded:• The personal computer has entered standby mode duringcharging. (*)• The personal computer has entered standby mode duringcharging. (*)• The personal computer has entered standby mode during• The available power is insufficient because other equipment isconnected to other USB ports.• Charging has been paused for temperature protection.• During charging of one battery, another battery has been added.(*) Please refer to the instructions for your computer and cancel standby mode.– – – – – – – – Approx. every 1.5 sec Charging– – – – – – – – Approx. every 1.5 sec Charging––––––––––– Steady Charging completed (*)––––––––––– Steady Charging completed (*)- - - - - - - - - - - Approx. every 0.5 sec Battery abnormal- - - - - - - - - - - Approx. every 0.5 sec Battery abnormalNot lit Stop during charging (computerNot lit Stop during charging (computerstandby mode etc.)(*) When two batteries are being charged, the condition where charging of bothbatteries has been completed.LED Charge indication lightLED Charge indication lightAdjuster (+) contactRaise for AA batteriesLower for AAA batteries(-) contact for AAand AAALED Charge indicatorCordUSB connectorUSB housingRaise the adjuster for AA batteriesster for AAA batteries• This charger is only for AA and AAA Ni-MHbatteries made by SANYO.• Do not attempt to charge alkaline batteries.• Do not connect equipment to other USB ports whilecharging. The available power required may beexceeded and the computer may be damaged or datamay be lost.• Do not connect via a USB connection cable. This maycause interference with other electrical equipment.• Do not use the charger in areas of high humidity orwhere it may be exposed to water.• Insert the batteries into the charger with matchedpolarity.• Disconnect the charger from the port aftercompletion of charging.• Lower the adjuster when the charger is not beingused. Put the USB connector into USB housing of thecharger.• Do not pull the USB connector and the cordexcessively.• Do not touch the charger or the batteries with wethands.• Use the charger in the temperature range from 0 °Cto 40 °C.• Do not insert Metallic objects other than eneloopbatteries into the charger.• Do not modify or disassemble the charger.• In case of abnormalities or trouble, disconnect theUSB connector from the computer port and contactyour dealer.• Keep the charger out of reach of small children. Ifchildren are to use the charger, keep them underobservation.• Do not store the charger in locations with highhumidity or dust.HOW TO INSERT THE BATTERYDepending on whether the adjuster is raised or not, one ortwo AA or AAA batteries can be charged.Adjuster (+) contactRaise for AA batteriesLower for AAA batteries(-) contact for AACordUSB connectorUSB housingRaise the adjuster for AA batteriesLower the adjuster for AAA batteries

/ 1

Related manuals for Sanyo NC-MDU01