Sanyo NC-MQN06 User Manual

Correctly use “eneloop”Ni-MH batteryAbout ChargingDepending upon storage condition, typically eneloop does not need tobe recharged for the first time if used within 2 years from themanufactured date. However, there may be a time when some digitalcameras may display the low battery indicator. In these cases, pleaserecharge.Charging SafetyDo not charge near hot temperatures like an electric blanket,stove, near direct sunlight, inside of a car, or under hot sun, etc. Inaddition, please do not cover the charger with a blanket. In suchcases, battery would not be fully charged because the temperatureinside of the charger will become hot, and the safety protectivefunction will be activated and stop charging.Please charge at temperature between 41°F to 95°F.Notes on Safety (Please read for proper use.)Severity of symbolDanger - Very close to causing death or heavy damageto human body.Warning - May cause death or heavy damage tohuman body.Caution - May cause heavy damage to human bodyor property damage.This symbol is to inform that the action written inside of thesymbol is prohibited. (Left is to prohibit you from taking apart)Safety issues of chargerRegarding eneloop Ni-MH batteriesDangerDanger• Do not dispose of in fire. Do not heat, deform, solder, dissamble ormodify.• Do not insert batteries with the (+) and (-) ends reversed.• If leaked liquid gets in the eyes, wash them with clean water andconsult a doctor immediately.• Batteries should not be used in underwater lighting or in sealedelectronic devices.Warning• Do not connect the (+) and (-) ends with metal objects. Whencarrying or storing batteries, avoid direct contact with metal objects.• Children should be supervised while handling the batteries.• Do not peel off or damage the outer tube.• If leaked liquid gets on the skin or clothing, wash off with clean waterimmediately.• Do not connect 10 batteries or more in series.Please follow the instructions below to avoid damage or injury.CautionOperating temperature range for Ni-MH battery eneloopDo not use these batteries together with dry cells, other types ofbatteries, new or old batteries together, or batteries with differentcharge levels.• Discharge• Recharge• Store• Outside of the indicated range, battery’s performance andlife-cycle may decrease.23°F to 122°F41°F to 95°F- 4°F to 86°FStatusChargingproperlyFinishchargingDefaultmodeHandlingNormalBatteries are ready for usea) No battery put inside chargerb) Battery connected incorrectlyc) The charger has internal failured) Power offIndication lightAppearanceIndicator lights flashingIndicator lights are offIndicator lights are onParts and usageWith this charger, you cancharge up to 4 AA or 4AAAeneloop Ni-MH batteries.AAA (-) contact surfaceAA (-) contact surfaceCharge indicator light• Flashes when charging.• Turns on when charging iscomplete.How to insert and remove batteryHow to insert• Match the + and – terminal of thebattery with the charger’s + and– contact surface.• For AA battery, insert from the+ terminal and push on the– terminal.• For AAA battery, insert from– terminal as in the picture, thenplace + terminal into + contact surface.How to insert a AA batteryHow to insert a AAA batteryHow to remove• For AA battery, take out from– terminal.• For AAA battery, if pushed onthe + side, - side will pop outfor easy removal.How to charge1) This charger is designed to charge 2 or 4 pcs of AA or AAANi-MH rechargeable batteries. AA and AAA batteries can becharged at the same time.2) If you want to charge 4 pcs of AA or AAA, put batteries into thecharger compartments, taking care to observe polarity (+/-) asindicated inside the charger.3) If only charging 2 batteries at a time, place the batteries in theleft or right side compartments of the charger.4) Swing plug out and plug into AC100-240V outlet.5) Confirm that the indication lights begin to flash. Do not plug inupside down. If plugged in upside down, it will finish chargingbefore it is fully charged.6) When charging is complete, the indicator lights will turn onconstantly. Refer to charging chart for typical charge time.7) After charging is done, unplug the charger from the outlet andswing plug back into place.Use under the specified voltagePlease use under AC100V to 240V. Otherwise, maycause high heat, fire breakout, electric shock, or harm tohuman body.WarningCautionMay deform charger causing high heat, leakage,or explosion.Do not allow metal objects come into contact with charger.May cause electric shock, excessive heat, or fire.Do not place heavy objects on top of the charger. Avoidunstable locations like areas with strong magnetic fields ordust. May cause excessive heat or fire.This appliance is not intended for use by persons(including children) with reduced physical, sensory ormental capabilities, or lack of experience and knowledge,unless they have been given supervision or instructionconcerning use of the appliance by a person responsiblefor their safety. Children should be supervised to ensurethat they do not play with the appliance. Do not chargenon-rechargeable batteries.Charger should be used between 41°F to 95°F. If ambienttemperature is higher, charger may cause the battery to leakor rupture.SpecInputOutputAC100-240V ~ 50/60Hz 8WAA - 2/4 x 1.2V — 300mAAAA - 2/4 x 1.2V — 150mASizeWeightTemp. range118 x 72 x 32.5 mm~ 98g41°F – 95°FSuitable Battery Charge time1 – 4 batteryApprox. 7 hoursAA HR-3UTG ( Max 3000mAh.Min. 1900mAh*)Ni-MHbatteryeneloopApprox. 10 hoursCharge time is the time it takes to charge a fully discharged battery.The charge time will depend on the remaining charge in the batteryand the ambient temperature.AAA HR-4UTG (Max 1000mAh.Min. 750mAh*)Please recycle used rechargeable batteries.All rechargeable batteries contain preciousresources that can be reused. To learn moreabout recycling or to find a drop-off location,please visit http://www.rbrc.orgCall GE SANYO at (866) 848-9912 • SANYO Energy (U.S.A.) Corp.,c/o XWG, 1840 County Line Road Huntingdon Valley, PA 19006sanyo@accessoryhelp.info • www.sanyobatteries.comExample of the symbols* All statements concerning capacity (mAh) or the life of the battery (cyclelife) are based on IEC61951-2.* Statements concerning long term storage is based on simulations at roomtemperature.How to assemble C or D battery• Match the + and – terminal of a AA eneloop battery with thespacer’s + and – terminals.• Insert the + terminal of the AA eneloop battery into the – end ofthe spacer.• Push the AA battery until it “snaps” into place.• To remove, push on the + terminal of the AA eneloop batteryuntil it releases.AA batteryC or D spacerCharger Model #NC-MQN06For customer service issues, please call 1-866-848-9912or visit us online at www.sanyobatteries.com.

/ 1

Related manuals for Sanyo NC-MQN06