Sanwa ExzesX Operating Manual

Sanwa ExzesX Operating Manual Manual pdf 4 page image

Page 4USagE PREcaUTiOnSTRanSMiTTER PREcaUTiOnSIn addition to the Safety and FCC Compliance sections on the previous page, please observe the following precautions wheninstalling and using your Sanwa EXZES X 2.4GHz FHSS-3 radio control system.l The receiver antenna consists of a coaxial cable and a reception wire (the thin tip at the end of the coaxial cable). When youmount the receiver antenna, do not bend the reception wire. Reception performance decreases if the reception wire is bent.l The antenna wire is delicate, therefore, handle with care. Do not pull on the antenna wire with force. Do not cut or extend theantenna wire.l The coaxial cable (the thicker portion or the antenna) can be bent into gentle curves, however, do notbend the coaxial cable acutely, or repeatedly bend it, or the antenna core can be damaged.l The antenna wire should be installed into a vertical plastic tube per your particular model's assembly instructions. Keep thereceiver antenna as far away from the motor, battery, and ESC as possible.l There is a danger of runaway operation if connectors shake loose during use. Make sure that the receiver,servo(s), and switch connectors are securely fitted.l The receiver is susceptible to vibration, shock, and moisture. Take appropriate measures to protect againstvibration and moisture. Failure to take appropriate measures could result in runaway operation or damage tothe receiver. We suggest wrapping the receiver in shock-absorbing foam when installing it into your model.l When installing the receiver, avoid contact with any carbon or metal chassis components.l Contact between metal parts mounted on a model can result in electrical noise, which can adversely effectreceiver performance and possibly result in runaway operation or damage to your model.l With electric-powered models, be sure to fit the motor with a noise suppression capacitor. Without a noise suppressioncapacitor, excessive electrical noise generation can cause runaway operation and/or result in damage to your model.l Use rubber anti-vibration absorbers with servos. Direct transmission of engine vibration to servos can cause servo failure andpossibly result in runaway operation with damage to your model.l Turn the transmitter ON first, then turn the receiver ON. After using your model, turn the receiverOFF first, then turn the transmitter OFF. It can be dangerous if you Activate the components inreverse order as the servos may start up inadvertently.l Before use, double-check that the transmitter and receiver batteries have sufficientpower and/or are sufficiently charged.l Never touch the transmitter antenna during use. Doing so may cause loss of transmitter output, making itimpossible to control your model.l The transmitter antenna should be rotated and angled so that the antenna is as close to perpendicular to the ground aspossible during use. After use, to prevent any chance of damaging the antenna, the antenna should berotated and moved into the horizontal stowed position.l Do not expose the transmitter to excessive heat, moisture, fuel, exhaustresidue, etc. Do not expose the transmitter to excessive heat or direct sunlight.Leaving the transmitter in direct sunlight can damage the LCD.l Do not press the Bind Button during use. The signal is interrupted while the Bind Button is pressed. Itmay also require a short time to restore the signal after releasing the Bind Button, which can be dangerous.l If the outer case becomes dirty, it can be cleaned with a soft dry cloth. If the outer case becomes soiled, it can be cleaned witha damp cloth and liquid detergent. Do not use any solvents to clean the outer case. Solvents will damage the finish.REcEivER PREcaUTiOnS2.4gHz FREqUEncY BanD PREcaUTiOnSl The 2.4GHz frequency band may be used by other devices, or other devices in the immediate area may cause interference onthe same frequency band. Always before use, conduct a bench test to ensure that the servos operate properly. Also, conductchecks with the transmitter as distant as possible from your model.l The response speed of the receiver can be affected if used where multiple 2.4GHz radio controllers are being used, therefore,carefully check the area before use. Also, if response seems slow during use, stop your model immediately and discontinue use.l If the 2.4GHz frequency band is saturated (too many radio controllers on at once), as a safety precaution, the radio controlsystem may not bind. This ensures that your radio control system does not get hit by interference. Once the frequencies havebeen cleared, or the saturation level has dropped, your radio control system should be able to bind without any problems.Antenna TubeCoaxial CableAntennaReception Wire