Samsung QB65H Quick Setup Manual

Also see for QB65H: User manual User manual User manual User manual User manual

Quick Setup Guide− Recommended hours of use per day of this product is under 16 hours. If the product is used for longer than16 hours a day, the warranty may be void.− The colour and the appearance may differ depending on the product, and the specifications are subjectto change without prior notice to improve the performance.− Download the user manual from the website for further details.http://www.samsung.com/displaysolutionsQB65H QB75HBN68-07849G-00The terms HDMI and HDMI High-Definition Multimedia Interface,and the HDMI Logo are trademarks or registered trademarks ofHDMI Licensing LLC in the United States and other countries.Reverse Side1 Connect to a USB memory device.‐ The USB ports on the product accept a maximum constantcurrent of 1.0A. If the maximum value is exceeded, USB portsmay not work.2 Connects to MDC using a LAN cable.3 Connects to MDC using an RS232C adapter.4 DVI: Connects to a source device using a DVI cable or HDMI-DVI cable.MAGICINFO IN: To use MagicInfo, make sure to connect theDP-DVI cable.5 Connects to a source device using a HDMI cable or HDMI-DVIcable.6 Connects to a PC using a DP cable.7 Connect to a USB memory device.‐ The USB ports on the product accept a maximum constantcurrent of 0.5A. If the maximum value is exceeded, USB portsmay not work.8 Receives sound from a PC via an audio cable.9 Connects to the audio of a source device.0 Supplies power to the external sensor board or receives the lightsensor signal.! Connects to MDC using an RS232C adapter.Issues SolutionsThe screen keepsswitching on and off.Check the cable connection betweenthe product and PC, and ensure theconnection is secure.No Signal is displayedon the screen.Check that the product is connectedcorrectly with a cable.Check that the device connected to theproduct is powered on.Depending on the type of external device,the screen may not display properly. Inthis case, connect it with the HDMI HotPlug function turned On.Not Optimum Mode isdisplayed.This message is displayed when asignal from the graphics card exceedsthe product’s maximum resolution andfrequency.Refer to the Standard Signal Mode Tableand set the maximum resolution andfrequency according to the productspecifications.The images on thescreen look distorted.Check the cable connection to theproduct.The screen appearsunstable and shaky.Check that the resolution and frequencyof the PC and graphics card are set withina range compatible with the product.Then, change the screen settings ifrequired by referring to the AdditionalInformation on the product menu and theStandard Signal Mode Table.There are shadows orghost images left onthe screen.Issues SolutionsThere is no image onthe screen and thepower LED blinksevery 0.5 to 1 second.The product is in power-saving mode.Press any key on the keyboard or move themouse to return to the previous screen.Picture quality of theproduct is differentfrom the dealershop where it waspurchased.Use an HDMI cable to obtain high-definition (HD) picture quality.The remote controldoes not work.Make sure that the batteries are correctlyin place (+/-).Check if the batteries are flat.Check for power failure.Make sure that the power cord is connected.Check for any special lighting or neonsigns switched on in the vicinity.A beeping sound isheard when my PC isbooting.If a beeping sound is heard when your PCis booting, have your PC serviced.When I try to changethe PC resolution, amessage Thedefined resolutionis not supported.appears.The message The defined resolutionis not supported. appears if the inputsource resolution exceeds the maximumresolution of the display.To resolve the issue, change the PCresolution to a resolution supported onthe display.Troubleshooting GuideChecking the Components Control PanelContact the vendor where you purchased the product if anycomponents are missing.The pictures may look different from the actual components.1 Spacer logoDo not pull on the spacer logo using force. The logo may tear or break off.2 Remote sensorPress a button on the remote control pointing at the bottom of theproduct face to perform the function. The remote control sensor islocated on the bottom of the product.- Using other display devices in the same space as the remotecontrol of this product can cause the other display devices to beinadvertently controlled.3 Panel Key4 Power on the product. If you press the button when the productis turned on, the control menu will be displayed.- To exit the OSD menu, press and hold the panel key for at least one second.5 Move to the upper or lower menu. You can also adjust the value of an option.6 Move to the left or right menu.Quick Setup GuideWarranty card(Not available in somelocations)MagicInfo SoftwareDVDPower cordBatteries(Not available in somelocations)Remote ControlRS232C(IN) adapter HOLDER-CABLE(3 EA)QB65HQB75HSpeakerSpeaker

/ 2

Related manuals for Samsung QB65H