Samsung CY-SWC1000A User Manual

EnglishEnglish-1Wireless Charger (Model: CY-SWC1000A )User Manual1. Product OverviewThis product enables you to charge the 3D Active Glasses wirelessly. To charge the product,you have to use this product with the 3D Active Glasses.2. Part Names and AccessoriesAccessories : Wireless charger, Adapter, AC-cord, Manual, Ferrite Core3. How to Useyy Connect the power cord to the adapter at the back of the product.yy Connect the adapter supplied with the product to the AC power cord.yy When the LED at the top of the product turns red and you press the power switch slightly,the LED turns green and the product enters charging mode. At this time, the blue LED atthe front starts blinking slowly. During charging mode, the green LED at the top turns onand the blue LED at the front blinks so that you can easily identify the state. (This productsupports a last memory function that saves the last settings even if the power is turned off.The LED may illuminate green according to the state when the power was last turned off.Since the green LED indicates that the product is already in charging mode, in this case,proceed to the next step without pressing the power button.)yy In charging mode, put the device that supports wireless charging on the correspondingpart of the product to start charging the device. Charging will start automatically. It isrecommended that you only use the following authorized devices that support wirelesscharging.y✎ To charge the 3D Active Glasses (SSG-3300GR, SSG-3300CR, SSG-3700CR) that supportwireless charging and that are sold separately, put the glasses on the circular wing as shownby the figure so that the front of the glasses face outward. At this time, make sure to check thecharge status of the glasses through the LED of the 3D Active Glasses. If the LED of the 3DActive Glasses is off, it indicates that the glasses have not been placed in position properly. TheLED on the 3D glasses will blink while the battery is being charged. Move the glassesuntil the red LED flashes. The battery is fully charged when the LED on the 3D glassesturns green and flashes. It is best to place the glasses within the recommended area of use(marked by oblique lines) indicated in the following picture. If the glasses are outside of therecommended area, charging may take longer.y✎ If charging is complete or is not necessary, press the power button at the top once. The powerLED illuminates red and the product changes to standby mode. This product provides an automaticmode switching function to save power. Approximately 5 hours after the green LED is illuminated,the product automatically changes from charging mode to standby mode and then the LEDilluminates red.4. Operating Precautionsy Charging another device that is not specified in the manual is not guaranteed. Do notplace or stack incompatible devices on the product.y If the charging function of the product is no longer necessary or the device has been fullycharged, it is recommended that you switch to standby mode by pressing the powerbutton. In the standby state, the product does not emit a magnetic field and consumesnegligible power.y The product provides an auto-power off function to save power. Approximately 5 hoursafter entering charge mode (green LED), the product automatically enters standby mode(red LED). Please note that is not a product malfunction.y This product supports the last memory function that saves the last settings even if thepower is turned off. In the case of a power failure or when the AC adapter or the DC jackis disconnected, the product remembers the last mode such as charge mode or standbymode and automatically returns to that mode when power is supplied again. This is not aproduct malfunction.y Since the circuitry is located at the bottom of the product, it may generate heat, but theheat is within the safety specifications and this is not a malfunction of the product.y This product generates a magnetic field. Do not place the product near wireless devices(a mobile phone, etc.), contactless cards or, communication equipment. The device mayinterfere with the product and cause it to become damaged.y Since this product utilizes electro-magnetic resonance, the internal antennas may interferewith each other. When using this product, avoid stacking the products or placing themwithin 30 cm of each other.y The charging time may be affected by the age of the battery in the device to be chargedor the charge method, and the model of the product. For more information, please referG AGIB;Power switch and LEDDC adapter socket(at the bottom back)LED charging modeCircular wingSuggested rangeCylinder topCircular wing 1.5cm (0.6 in)Suggested range(marked by oblique lines)Circular wingCY-SWC1000A_Na_L16.indb 1 2011-02-17 오후 1:19:07