Samsung BN68-02664A-03 Quick Setup Manual

Contents

quick setup guide

English - 1Quick Setup Guide1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.To register this product, visit : www.samsung.com/register.Congratulations on the purchase of your new Samsung TV. Read thissetup guide to get your TV up and running quickly.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 4 : Connect External DevicesConnecting an AV device (Blu-ray player, cable/satellite box, etc.) Connecting an audio deviceConnect your TV to your Home Theater or other audiodevice to enjoy enhanced sound quality.Connecting a PCConnect your TV to a PC to use it as a Monitor.Getting StartedFor the very best picture quality, select HD signal sources and use HDMI cables andconnections. Note that many digital cable programs are not in HD. Check with your videoprovider to ensure your are receiving HD signals.• Wall cable jack or• VHF/UHFAntenna or• Cable or Satellitebox Ant or CableOutStep 3 : Connect Power and Antenna or CableMake sure the AC power cordis plugged in securely to thewall outlet and the TV.Use a 75 ohm (round) cable.orStep 2 : Install the Batteries into the RemoteTo install batteries into your remote control, follow these steps:1. Lift the cover on the back of the remote upwardas shown in the figure to the right.2. Install two AAA batteries.Make sure to match the + and - ends of✎ the batteries to the diagram in the batterycompartment.3. Replace the cover.Connect AnT In to:Step 1 : Install the StandFollow the steps below to connect the TV to the stand.Make sure to distinguish between the front and back of the Stand and Guide✎ Stand when assembling them.Make sure that at least two people lift and move the LCD TV.✎ Lay the product down, with the screen facing up and fasten the screws.✎Power Input12Lowest Quality ConnectionUsing an HDMI CableDVD / Blu-Ray player / HD Cable Box /HD Satellite receiver (STB)HDMI OUT DeviceAV IN 2(HDD)USB1SB2AV IN 2(HDD)USB1SB2 HDMI IN 4HD connection (up to 1080p)Best ConnectionUsing a Component CableVCR / DVD / Blu-ray player / Cable Box/ Satellite receiverComponent connection (up to 1080p)Device(HDD)USB1USB2 (HDD)USB1USB2 HDMI IN 4AV IN 2COMPONENT OUTGood ConnectionAUDIO OUTHD connection (up to 1080p)Very Good ConnectionUsing an DVI to HDMI CableDVD / Blu-Ray player /Cable Box /Satellite receiver (STB)DeviceAV IN 2(HDD)USB1USB2AV IN 2(HDD)USB1USB2 HDMI IN 4DVI OUTAUDIO OUTUsing an Audio/Video CableVCR / DVD / Blu-ray player / Cable Box /Satellite receiverAudio/Video connection (480i only)VIDEO OUT VCR(HDD)USB1USB2 (HDD)USB1USB2 HDMI IN 4AV IN 2AUDIO OUTWhen connecting to✎ AV In on the back of your TV, attach the videocable (yellow) to the green jack next to the AV In 1 label. The jack willnot match the color of the video cable (yellow).The HDMI connection carriesdigital video and audio.Using an D-Sub CableAUDIO OUTPC OUTPCUsing an HDMI CableHD connectionDVI OUTAUDIO OUTPCDigital Audio connectionUsing an Optical CableDigital Audio SystemOPTICALUsing an Audio CableAmplifier / DVD Home TheaterAnalog Audio connectionDeviceAV IN 2(HDD)USB1SB2AV IN 2(HDD)USB1SB2 HDMI IN 4AUDIO INStep 5 : Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language,set the clock mode, and launch the TV’s channel memorizing process. It alsodisplays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Rightarrow buttons on your remote. To make a selection, press the EnTErE button.To skip a screen, press the MEnU button.To turn on your TV, press the POwEr button on the remote or press thePOwEr button on the TV. To run Plug & Play, follow these steps:Select Language of the OSD.Language : EnglishU Move E EnterPlug & PlayEnglishEspañolFrançais1. On the Language screen, select the language for the On Screen Display(OSD) using your remote control, and then press EnTErE button. TheHome Use screen appears.2. Select Home Use, and then press EnTErE button. If you select StoreDemo, the TV will reset your picture and audio settings every 30 minutes. Afteryou press EnTErE button, the Antenna Source screen appears.3. If your TV is only attached to an antenna, select Air. If your TV is onlyattached to cable and you have no cable box, select Cable. If your TV isattached to an antenna and cable with no box, select Auto. When done,press EnTErE button on your remote. The Select Cable System screenappears.IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,according to the directions for your cable or satellite box.4. If your TV is attached to a cable system and you have no cable box, youmust select your cable system type. If you have Digital cable, you mustselect the cable system type for both Analog and Digital. After youhave selected the cable system type, select Start, and then press theEnTErE button on your remote.Most cable systems are Standard✎ (STD) systems. If you are notsure about what kind of cable system you have, contact your cablecompany.5. The TV memorizes the available channels. This process can take up to45 minutes. After the TV has memorized the channels, the Clock Modescreen appears.6. Choose the Clock Mode. Select Auto if you have a digital channel inyour area. Select Manual if you don’t, or if you have a cable or satellitebox. When done, press EnTErE button. The Daylight Savings screenappears.If you select✎ Manual, the clock setting screen appears.7. Select the Daylight Saving Time setting: Off, On, or Auto, and thenpress EnTErE button.8. After the time zone screen, The connection method for best HD screenquality is displayed. Press Right arrow button on your remote to view eachscreen in succession. Press the BLUE button to skip this section.9. The Enjoy your TV screen appears. and then press EnTErE button.Changing the Screen SizeYour TV has several screen size options, each designed to work best with specifictypes of video input. If you have a cable box or satellite receiver, it may have its ownset of screen sizes as well.To change the screen size, press the P.SIzE button on your remote. The first timeyou press it, your TV displays the current setting. Thereafter, each time you press theP.SIzE button, you change the size of the picture on the screen.The following sizes are available:Screen Fit✎ displays a full HD picture covering the entire screen with no cutoff onany side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p),Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.16:9 Wide screenWide FitZoom 14:3 Standard screenZoom 2Screen FitBasic FunctionsStandScrew

/ 2

Related manuals for Samsung BN68-02664A-03