Samsung BN68-02662A-01 Quick Setup Manual

Contents

quick setup guide

Quick Setup GuideCongratulations on the purchase of your new Samsung TV.Read this setup guide to get your TV up and running quickly.1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12AM EST.To register this product, visit: www.samsung.com/register.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 1: Install the StandFollow the steps below to connect the TV to the stand.✎ NOTEx Make sure to distinguish between the front and back of the Stand andGuide Stand when assembling them.x Make sure that at least two people lift and move the LED TV.x Stand the product up fasten the screws. If you fasten the screws with thewith the LED tv placed down, it may lean to one side.[ Do not insert your fingers into the stand base slot of the TV wheninstalling the stand base.1 Connect the Guide Stand to theStand using four screws(M4 X L12) as shown.s ssssTop viewGuide StandScrews (M4 X L12)StandRear2 With your TV upright, connect theTV to the Stand as shown.3 Fasten two screws (M4 X L8) atposition 1, and then fasten threescrews (M4 X L8) at position 2.sssss1sssss2Step 2: Install the Batteries into the RemoteTo install batteries into your remotecontrol, follow these steps:1. Lift the cover on the back ofthe remote upward as shownin the figure to the right.2. Install two AAA batteries.✎ Make sure to match the+ and - ends of the batteries to the diagram in the battery compartment.3. Replace the cover.Step 3: Connect Antenna or CableConnecting an audio device (Home Theater, etc.)Connect your TV to your Home Theater or other audio device to enjoy enhancedSound quality.Connecting a PCConnect your TV to a PC to use it as a Monitor.Using an EX-Link Cable ConnectionAvailable Devices : External devices that support EX-LinkEX-LINK : Connector for service only.RearFrontStep 4: Connect External DevicesConnecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.HDMI OUTAUDIO OUTDVI OUTAUDIO OUTCOMPONENT OUTVIDEO OUTVIDEO OUTAUDIO OUTUsing an HDMI CableHD connection (up to 1080p)Best ConnectionDeviceUsing an HDMI to DVI CableVery Good ConnectionComponent connection (up to 1080p)DeviceGood Connection Lowest Quality ConnectionComponent connection (up to 1080p) Audio/Video connection (480i only)Using a Component Cable Using an Audio/Video CableDeviceHDMI Cable (Not Supplied)HDMI to DVI Cable (Not Supplied)Audio Cable(Not Supplied)Component Cable(Not Supplied)Audio Cable(Not Supplied)Audio Cable (Not Supplied)Video Cable(Not Supplied)AUDIO INOPTICALAnalog Audio connectionDigital Audio connectionAmplifier / DVDhome theaterDigital Audio SystemUsing an Audio CableUsing an Optical CableAudio Cable (Not Supplied)Optical Cable (Not Supplied)DVI OUTAUDIO OUTAUDIO OUTPC OUTHD connectionUsing an HDMI to DVI CableUsing an D-Sub CableOptical Cable (Not Supplied)Audio Cable (Not Supplied)Audio Cable(Not Supplied)D-Sub Cable(Not Supplied)DeviceDVD, Blu-ray player, cable box,STB satellite receiver, VCR DVD, Blu-ray player, cable box,STB satellite receiver, VCRDVD, Blu-ray player, HD Cable Box, HDSTB (Set-Top-Box) satellite receiverStep 5: Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language,set the clock mode, and launch the TV’s channel memorizing process.It also displays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Right arrowbuttons on your remote. To make a selection, press the ENTERE button.To skip a screen, press the MENU button. To turn on your TV, press the POWERbutton on the remote or on the TV. To run Plug & Play, follow these steps:1 Using your remote control, selectthe language for the On ScreenDisplay (OSD), and then press theENTERE button.2 Select Home Use, and thenpress the ENTERE button. Ifyou select Store Demo, the TVwill reset your picture and audiosettings every 30 minutes.3 Select Antenna Source tomemorize. If Antenna Source isCable or Auto, you must selectAntenna Source to same typeas your cable system type. Afterselecting source, select Search;then press the ENTERE buttonon your remote.✎ Most cable systems areStandard(STD) systems, If you arenot sure about what kind of cablesystem you have, contact your cable company.✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. AfterPlug & Play is complete, set your TV to Channel 3 or 4, according to thedirections for your cable or satellite box.4 The TV memorizes the availablechannels. This process can takeup to 45 minutes.5 After the TV has memorized thechannels, choose the ClockMode. Select Auto if you havea digital channel in your area.Select Manual if you don’t, or ifyou have a cable or satellite box.When done, press the ENTEREbutton.✎ If you select Manual, the clocksetting screen appears.6 Select the daylight savings timesetting: Off or On, and then pressthe ENTERE button.7 Select the time zone in whichyou live, and then press theENTERE button.8 After the time zone screen, The connection method for best HD screenquality is displayed. Press Right arrow button on your remote to view eachscreen in succession. Press the Blue button to skip this section.9 The Enjoy your TV. screen appears. Then press the ENTERE button.If You Want to Rerun Plug & Play1. Press the SOURCE button on your remote, then select TV mode.2. Press the MENU button on your remote to display the menu.3. Press the ▲ or ▼ button to select Setup, and then press ENTERE.4. Press ENTERE again to select Plug & Play.Previous U Move E EnterSelect the usage mode.Store Demo Home UsePlug & PlayU Move E EnterAnrenna Source :Digital Cable System :Analog Cable System :AirCableAutoSearchPlug & PlayU Move E EnterSelect Language of the OSD.Menu Language :Plug & PlayEnglishEspañolFrançaisU Move E EnterSet to daylight saving time.DST : OffOnPlug & PlayE EnterRemoving scrambled channel.DTV Cable 1476%DTV Air 0 12212 52AirDTV Cable CableStopPlug & PlayU Move E EnterSet the Clock Mode.Clock Mode : AutoManualPlug & PlayVHF/UHF AntennaConnect Ant In to• Wall cable jack• VHF/UHF Antenna• Cable or Satellite boxAnt or Cable OutUse a 75 ohm (round) cable.orMake sure the AC power cord is plugged in securely tothe wall outlet and the TV.Antenna Cable

/ 2

Related manuals for Samsung BN68-02662A-01