Samsung BN68-02621A-04 Quick Setup Manual

Contents

quick setup guide

English - 1• Wall cable jack or• VHF/UHFAntenna or• Cable or Satellitebox Ant or CableOutQuick Setup Guide1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.To register this product, visit : www.samsung.com/register.Congratulations on the purchase of your new Samsung TV. Read thissetup guide to get your TV up and running quickly.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 3 : Connect Power and Antenna or CableStep 4 : Connect External DevicesConnecting an AV device (Blu-ray player, cable/satellite box, etc.) Connecting an audio deviceConnect your TV to your Home Theater or other audiodevice to enjoy enhanced sound quality.Connecting a PCConnect your TV to a PC to use it as a Monitor.Use a 75 ohm (round) cable.Using an D-Sub CableAUDIO OUTPC OUTPCHD connectionUsing an HDMI CableDVI OUTAUDIO OUTPCStep 2 : Install the Batteries into the RemoteTo install batteries into your remote control, follow these steps:1. Lift the cover on the back of the remote upwardas shown in the figure to the right.2. Install two AAA batteries.Make sure to match the + and - ends of✎ the batteries to the diagram in the batterycompartment.3. Replace the cover.Connect AnT In to:Using an HDMI CableDVD / Blu-Ray player / HD Cable Box /HD Satellite receiver (STB)HDMI OUT DeviceAV IN 2(HDD)USB1USB2AV IN 2(HDD)USB1USB2 HDMI IN 4HD connection (up to 1080p)Best ConnectionStep 1 : Install the StandFollow the steps below to connect the TV to the stand.Make sure to distinguish between the front and back of the Stand and Guide✎ Stand when assembling them.Make sure that at least two people lift and move the LCD TV.✎Lay the product down, with the screen facing up and fasten the screws.✎Using a Component CableVCR / DVD / Blu-ray player / Cable Box/ Satellite receiverComponent connection (up to 1080p)Device(HDD)USB1USB2 (HDD)USB1USB2 HDMI IN 4AV IN 2COMPONENT OUTGood ConnectionAUDIO OUTHD connection (up to 1080p)Very Good ConnectionUsing an DVI to HDMI CableDVD / Blu-Ray player /Cable Box /Satellite receiver (STB)DeviceAV IN 2(HDD)USB1USB2AV IN 2(HDD)USB1USB2 HDMI IN 4DVI OUTAUDIO OUT12Digital Audio connectionUsing an Optical CableDigital Audio SystemOPTICALUsing an Audio CableAmplifier / DVD Home TheaterAnalog Audio connectionDeviceAV IN 2(HDD)USB1USB2AV IN 2(HDD)USB1USB2 HDMI IN 4AUDIO INPower InputorGetting StartedFor the very best picture quality, select HD signal sources and use HDMI cables and connections.Note that many digital cable programs are not in HD. Check with your video provider to ensure yourare receiving HD signals.The HDMI connection carriesdigital video and audio.Step 5 : Run Plug & PlayWhen you turn on your TV for the first time, it automatically launchesthe Plug & Play function. With Plug & Play, you can select the OnScreen Display language, set the clock mode, and launch the TV’schannel memorizing process. It also displays connection instructionssimilar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left orRight arrow buttons on your remote. To make a selection, press theEnTErE button. To skip a screen, press the MEnU button.To turn on your TV, press the POwEr button on the remote or pressthe POwEr button on the TV. To run Plug & Play, follow these steps:1Select Language of the OSD.Language : EnglishPlug & PlayU Move E EnterEnglishEspañolFrançaisOn the Language screen, select the language for the On ScreenDisplay (OSD) using your remote control, and then pressEnTErE button. The Home Use screen appears.2Select ‘Home Use’ when installing this TV in your home.Plug & PlayL Move E EnterStore Demo Home UseSelect Home Use, and then press EnTErE button. If you selectStore Demo, the TV will reset your picture and audio settings every30 minutes. After you press EnTErE button , the Antenna Sourcescreen appears.3Select the Antenna source to memorise.AirCableAutoPlug & PlayU Move E Enter m SkipStartStartStartIf your TV is only attached to an antenna, select Air. If your TV is onlyattached to cable and you have no cable box, select Cable. If yourTV is attached to an antenna and cable with no box, select Auto.When done, press EnTErE button on your remote. The SelectCable System screen appears.IMPORTANT: If your TV is attached to a cable or satellite box,skip Steps 3 through 5. After Plug & Play is complete, set your TV toChannel 3 or 4, according to the directions for your cable or satellite box.4Selects the cable system.AnalogDigitalPlug & PlayU Move E Enter m SkipSTD HrC IrCSTD HrCStartIrCIf your TV is attached to a cable system and you have no cable box,you must select your cable system type. If you have Digital cable, youmust select the cable system type for both Analog and Digital.After you have selected the cable system type, select Start, and thenpress the EnTErE button on your remote.Most cable systems are Standard✎ (STD) systems. If you are notsure about what kind of cable system you have, contact yourcable company.5Auto Program in Progress.DTV Cable : -- Cable : -- Cable 28Plug & PlayE Enter m SkipStop15%The TV memorizes the available channels. This process can takeup to 45 minutes.6Set the Clock Mode.Clock Mode : EnglishPlug & PlayU Move E Enter m SkipAutoManualAfter the TV has memorized the channels, choose the ClockMode. Select Auto if you have a digital channel in your area. SelectManual if you don’t, or if you have a cable or satellite box. Whendone, press EnTErE button.If you select✎ Manual, the clock setting screen appears.7Set to daylight saving time.DST : EnglishPlug & PlayU Move E Enter m SkipOffOnAutoSelect the daylight savings time setting: Off, On, or Auto, and thenpress EnTErE button.8After the time zone screen,The connection methodfor best HD screen qualityis displayed. Press Rightarrow button on yourremote to view each screenin succession. Press theMEnU button to skip thissection.9 The Enjoy your TV screenappears. Then pressEnTErE button.StandScrewLowest Quality ConnectionUsing an Audio/Video CableVCR / DVD / Blu-ray player / Cable Box /Satellite receiverAudio/Video connection (480i only)VIDEO OUT VCR(HDD)USB1USB2 (HDD)USB1USB2 HDMI IN 4AV IN 2AUDIO OUT

/ 2

Related manuals for Samsung BN68-02621A-04