Samsung BN68-02911A-02 Quick Setup Manual

Contents

quick setup guide

Step 4: Connect External DevicesConnecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)Step 1: Install the StandFollow the steps below to connect the TV to the stand.✎ NOTEx Make sure to distinguish between the front and back of the Stand andGuide Stand when assembling them.x Make sure that at least two persons lift and move the LED TV.x Stand the product up and fasten the screws. If you fasten the screws withthe LED TV placed down, it may lean to one side.1 Connect the Guide Stand to theStand using four screws (M4 X L8)as shown.2 With your TV upright, connect theTV to the Stand.3 Fasten two screws (M4 X L8) atposition 1, and then fasten threescrews (M4 X L8) at position 2.s s ssssRearScrews (M4 X L8)sssss12Step 2: Install the Batteries into the RemoteTo install batteries into your remote control,follow these steps:1. Lift the cover on the back of the remoteupward as shown in the figure to theright.2. Install two AAA batteries.✎ Make sure to match the + and - ends of the batteries to the diagram inthe battery compartment.3. Replace the cover.Step 3: Connect Power and Antenna or CableQuick Setup GuideCongratulations on the purchase of your new Samsung TV.Read this setup guide to get your TV up and running quickly.1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12AM EST.To register this product, visit: www.samsung.com/register.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 5: Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language, setthe clock mode, and launch the TV’s channel memorizing process.It also displays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Right arrowbuttons on your remote. To make a selection, press the ENTERE button.To skip a screen, press the MENU button. To turn on your TV, press the POWERbutton on the remote or on the TV. To run Plug & Play, follow these steps:1 Using your remote control, selectthe language for the On ScreenDisplay (OSD), and then press theENTERE button.2 Select Home Use, and thenpress the ENTERE button.If you select Store Demo, the TV will reset your picture and audio settingsevery 30 minutes.3 Select Antenna Source. If Antenna Source is Air, Cable or Auto, you mustselect your cable system type. After selecting source, select Search; thenpress the ENTERE button on your remote.✎ Most cable systems are Standard (STD) systems, If you are not sure aboutwhat kind of cable system you have, contact your cable company.✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. AfterPlug & Play is complete, set your TV to Channel 3 or 4, according to thedirections for your cable or satellite box.4 The TV memorizes the available channels. This process can take up to 45minutes.5 After the TV has memorized the channels, choose the Clock Mode. SelectAuto if you have a digital channel in your area. Select Manual if you don’t, orif you have a cable or satellite box. When done, press the ENTERE button.✎ If you select Manual, the clock setting screen appears.6 Select the Daylight savings time setting: Off or On, and then press theENTERE button.✎ This function is only available when the Clock Mode is set to Auto.7 Select the time zone in which you live, and then press the ENTERE button.8 After the time zone screen, The connection method for best HD screenquality is displayed. Press the Right arrow button on your remote to vieweach screen in succession. Press the Blue button to skip this section.9 The Enjoy your TV. screen appears. Then press the ENTERE button.Changing the Screen SizeYour TV has several screen size options, each designed to work best with specifictypes of video input. If you have a cable box or satellite receiver, it may have its ownset of screen sizes as well.To change the screen size, press the P.SIZE button on your remote. The first timeyou press it, your TV displays the current setting. Thereafter, each time you pressthe P.SIZE button, you change the size of the picture on the screen.The following sizes are available:16:9 Widescreen 4:3 Standard screen Wide FitZoom 1 Zoom 2 Screen Fit✎ Screen Fit: Displays the full image without any cut-off when HDMI (720p /1080i / 1080p) or Component (1080i / 1080p) signals are inputted.Changing the Picture ModeYour TV has four preset Picture Modes with factory adjusted settings, eachdesigned to give you an excellent picture under specific conditions.The Picture Modes are listed and described in the table below:Mode DescriptionDynamic Brightens picture. For a vibrant, enhanced image in brightly lit orsunny room.Standard For a bright, detailed picture in a normally lit room.Natural For a comfortable, easy-on-the-eyes picture in a normally lit room.Movie For a studio quality cinema picture in a dimly lit or dark room.To change the Picture Mode, follow these steps:1. Turn on your TV, press the TOOLS button on your remote. The Tools menuappears.2. Using the ▲ or ▼ on your remote, select Picture Mode.3. On the Picture Mode menu, use the ◄ or ► button on your remote to selectthe Picture Mode you want.4. Press the EXIT button to exit the menu.Setting the ClockBefore you can use your TV’s On/Off Timer, you must set the clock. To set theclock, follow these steps:1. Turn on your TV, press the MENU button on your remote, then select Setup →Time.2. Select Clock Mode, and then press the ENTERE button.3. Choose Auto or Manual.x If you select Auto, the current time will be set automatically using the timefrom a digital channel.x If you select Manual, you can set the Month, Day, Year, Hour, Minuteand am/pm directly by pressing up, down, left and right arrow button onyour remote.4. Press the RETURN button on your remote when done.Connecting an audio device (Home Theater, etc.)Connecting a PCHDMI OUTAUDIO OUTCOMPONENT OUTAUDIO OUTDVI OUTAUDIO OUTVIDEO OUTAUDIO INOPTICALAnalog Audio connectionAmplifier / DVD home theaterUsing an Audio CableU Move E EnterSelect Language of the OSD.Menu Language :Plug & PlayEnglishEspañolFrançaisDVI OUTAUDIO OUTAUDIO OUTPC OUTHD connectionUsing an HDMI to DVI CableUsing a D-Sub CableDigital Audio connectionUsing an Optical CableDigital Audio SystemBest ConnectionHD connection (up to 1080p)Using an HDMI CableDVD, Blu-ray player, HD cable box,HD STB (Set-Top-Box) satellitereceiverDeviceHD connection (up to 1080p)Very Good ConnectionUsing an HDMI to DVI CableDeviceUsing a Component CableGood ConnectionComponent connection (up to 1080p)DVD, Blu-ray player, cable box,STB satellite receiver, VCRDeviceLowest Quality ConnectionAudio/Video connection (480i only)Using an Audio/Video CableDVD, Blu-ray player, cable box,STB satellite receiver, VCRDevices ssssTop viewRearGuide StandScrews (M4 X L8)StandUse one of the connections below to connect yourTV to an external A/V device.We recommend using HDMI for the highest picturequality.Connect your TV to your Home Theater or otheraudio device to enjoy enhanced Sound quality.Connect your TV to a PC to use it as a Monitor.VHF/UHF AntennaConnect Ant In to• Wall cable jack• VHF/UHF Antenna• Cable or Satellite boxAnt or Cable OutUse a 75 ohm (round) cable.orAntenna Cable(Not Supplied)Audio Cable (Not Supplied)HDMI to DVI Cable (Not Supplied)Audio Cable (Not Supplied)Audio Cable (Not Supplied) Component Cable (Not Supplied)HDMI Cable (Not Supplied)Video Cable (Not Supplied)Optical Cable (Not Supplied)Audio Cable (Not Supplied)HDMI to DVI Cable(Not Supplied)D-Sub Cable (Not Supplied)Audio Cable (Not Supplied)Audio Cable (Not Supplied)

/ 2

Related manuals for Samsung BN68-02911A-02