Reloop RMX 44 BT Instruction Manual

Also see for RMX 44 BT: Operation manual

Reloop RMX 44 BT Instruction Manual Manual pdf 1 page image

CAUTION! For your own safety, please read this operation manual carefully before initial operation! All personsinvolved in the installation, setting-up, operation, maintenance and service of this device must be appropriatelyqualified and observe this operation manual in detail. This product complies with the requirements of the appli-cable European and national regulations. Conformity has been proven. The respective statements and documentsare deposited at the manufacturer.Congratulations on purchasing your Reloop RMX44 BT mixing console. Thank you for placing your trust in our disc jockeytechnology. Before operating this equipment, we ask you to carefully study and observe all instructions.Please remove the Reloop RMX44 BT from its packaging. Check before initial operation to make sure that the device hasnot been visibly damaged during transport. If you detect any damage to the power cable or the casing, do not operate thedevice. Contact your specialised dealer.SAFETY INSTRUCTIONSCAUTION! Please exercise particular caution when handling AC 100 - 240 V, 50/60Hz power voltage. This voltagerating may lead to a critical electrical shock! Any damage caused by the non-observance of this operationmanual excludes any warranty claims. The manufacturer is not liable for any damage to property or for personalinjury caused by improper handling or non-observance of the safety instructions.- This device left the factory in perfect condition. To maintain this condition and to ensure a risk-free operation the usermust observe the safety instructions and warnings contained in this operation manual.- For reasons of safety and certification (CE) the unauthorised conversion and/or modification of the device is prohibited.Please note that in the event of damage caused by the manual modification to this device any warranty claims areexcluded.- The inside of the device does not contain any parts which require maintenance, with the exception of wear parts thatcan be exchanged from the outside. Qualified staff must carry out maintenance, otherwise the warranty does not apply!- The fuse must exclusively be exchanged against fuses of the same class, with the same trigger features and nominalcurrent rating.- Ensure that the power will only be supplied after the device has been fully set up. Always plug in the mains plug last.Ensure that the mains switch is in the “OFF” position when connecting the device to power.- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and correctly hooked up.Refer to your dealer, if you have any questions.- Ensure that when setting up the product, the mains cable is not squashed or damaged by sharp edges.- Prevent the mains cable from coming into contact with other cables! Exercise great care when handling mains cablesand connections. Never touch these parts with wet hands!- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to be used is a supplyoutlet in accordance with specifications of the public supply network.- Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to hold the mains plug bythe body. Never pull the mains cord!- Position the device on a horizontal and stable low-flame base.- Avoid any concussions or violent impact when installing or operating the device.- When selecting the location of installation, make sure that the device is not exposed to excessive heat, humidity and dust.Be sure that no cables lie around openly. You will endanger your own safety and that of others!- Do not rest any containers filled with liquid that could easily spill onto the device or in its immediate vicinity. If, however,fluids should access the inside of the device, immediately disconnect the mains plug. Have the device checked bya qualified service technician before re-use. Damage caused by fluids inside the device is excluded from warranty.- Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C) conditions. Keep thedevice away from direct exposure to the sun and heat sources such as radiators, ovens, etc. (even during transport in aclosed vehicle). Always ensure sufficient ventilation.- The device must not be operated after being taken from a cold environment into a warm environment. The condensationcaused hereby may destroy your device. Do not switch on or operate the device until it has reached ambient temperature!- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This device should only becleaned with a damp cloth. Never use solvents or cleaning fluids with a petroleum base for cleaning.- When relocating, the device should be transported in its original packaging.- When starting operation, the crossfaders and volume controls of your amplifier must be set to minimum level. Bringthe loudspeaker switches into the “OFF” position. Wait between 8 to 10 seconds before increasing the volume to avoiddamage to loudspeakers and diplexer.- Devices supplied by voltage should not be left in the hands of children. Please exercise particular care when in thepresence of children.- At commercial facilities the regulations for the prevention of accidents as stipulated by the organization of professionalassociations must be observed.- At schools, training facilities, hobby and self-help workshops the operation of the device must be monitored withresponsibility by trained staff.- Keep this operation manual in a safe place for later reference in the event of questions or problems.APPLICATION IN ACCORDANCEWITH REGULATIONS- This device is a professional mixing console which can regulate and mix low level audio signals. The device is therebyconnected between a signal source and an audio amplifier or active speakers, respectively.- This product is authorised for connection to 100 - 240 V, 50/60 Hz AC via mains adapter (included) and is designedexclusively for indoor application.- If the device is used for any other purposes than those described in the operation manual, damage can be caused tothe product, leading to the exclusion of warranty rights. Moreover, any other application that does not comply with thespecified purpose harbours risks such as short circuit, fire, electric shock, etc.- The serial number determined by the manufacturer must never be removed to uphold the warranty rights.MAINTENANCE- Check the technical safety of the device regularly for damage to the mains line or the casing, as well as for wear of wearparts such as rotary and sliding switches.- If it is to be assumed that the safe operation is no longer feasible, then the device must be disconnected and securedagainst accidental use. Always disconnect the mains plug from the outlet!- It must be assumed that a safe operation is no longer feasible, if the device bears visible defects, if the device no longerfunctions, following longer storage under unfavourable conditions or after major transport stress.2 2 2 22 2 2 25 5 5 57 7 7 78 8 8 86 6 6 691 1 1 14 4 4333613111222212019181415161723103224 31 26 25 2728 29 2929 30 291. OVERVIEW1.2 DESIGNATIONS1.2.1................... SIGNAL INPUT CHANNELS1. ..................... Signal Input Select Switch2. ..................... Gain Dial3. ..................... 3-Band Equalizer4. ..................... Master LEDs5. ..................... Filter6. ..................... Cue Button7. ..................... Linefader8. ..................... Crossfader Assign Switch9. ..................... Crossfader10. ..................... Crossfader Curve Switch1.2.2 ................. MIC CHANNEL11. ..................... Mic Level12. ..................... Level Control LED for Mic13. ..................... 2-Band Equalizer for Mic14. ..................... Mic Switch1.2.3 ................. HEADPHONES SECTION15. ..................... Mono/Stereo Split Select Switch16. ..................... Cue Mix (Cue/Master Signal Ratio)17. ..................... Cue Volume (Volume Control Headphones Output)1.2.4 ................. MASTER SECTION18. ..................... Master Volume19. ..................... LED for Master Signal20. .................... Balance Dial for Master Signal21. ..................... Booth Volume1.2.5 ................. CONNECTIONS22. .................... MIC Input23. .................... Headphone Out24. ..................... Power Connection25. .................... Master Out RCA26. .................... Master Out XLR (balanced)27. ..................... Booth Out28. ..................... Record Out29. .................... Channel Inputs30. .................... GND31. ..................... ON/OFF Switch32. .................... Bluetooth ButtonINSTRUCTION MANUAL43IMPORTANT NOTE:(For Mobile Device Configuration)FCC Radiation Exposure Statement:This equipment complies with FCCradiation exposure limits set forth foran uncontrolledenvironment. This equipment shouldbe installed and operated withminimum distance 20cmbetween the radiator & your body.IC IMPORTANT NOTE:(For Mobile Device Configuration)IC Radiation Exposure Statement:This equipment complies with ICRSS-102 radiation exposure limits setforth for an uncontrolledenvironment. This equipment shouldbe installed and operated withminimum distance 20cmbetween the radiator & your body.Industry Canada Caution:This device complies with IndustryCanada licence-exempt RSSstandard(s). Operation is subject tothe following two conditions:(1) this device may not causeinterference, and(2) this device must accept anyinterference, including interferencethat may cause undesired operationof the device.

/ 4

Related manuals for Reloop RMX 44 BT