Panasonic WV-CW474AFE Operating Instructions Manual

Panasonic WV-CW474AFE Operating Instructions Manual Manual pdf 1 page image

1. Camera Identification (CAMERA ID) SettingYou can use the camera identification (CAMERA ID) to assign a name to the camera. The camera IDconsists of up to 16 alphanumeric characters. The camera ID display can be switched on or off onthe monitor screen.To edit the CAMERA ID1. Move the cursor to CAMERA ID.The factory default setting is OFF.2. Press I(S). The CAMERA ID menu appears.The cursor on the letter “0” is highlighted.3. Move the cursor to the character you want to editby pressing I(L) / I(R) / I(U) / I(D).4. After selecting the character, press I(S). Theselected character appears in the editing area.(The pointer in the editing area moves to the rightautomatically at this moment.)5. Repeat the steps above until all characters areedited.To enter a blank space in the CAMERA IDMove the cursor to SPACE and press I(S).To replace a specific character in the CAMERA ID1. Move the cursor to the editing area by pressing I(D).2. Move the pointer to the character to be replaced by pressing I(L) or I(R). Then move thecursor to the character area and select a new character.3. Press I(S) to determine the CAMERA ID.To erase all characters in the editing areaMove the cursor to RESET and press I(S). All characters in the editing area disappear.To determine the display position of the CAMERA ID1. Move the cursor to POSI, and press I(S). The display at right appears and the CAMERA ID ishighlighted.2. Move the CAMERA ID to the desired position bypressing I(L) / I(R) / I(U) / I(D).3. Press I(S) to fix the position of the CAMERAID. The mode returns to the previous CAMERA IDmenu.Notes:• The CAMERA ID stops at the edges of themonitor screen.• The CAMERA ID moves faster if any of I(L) / I(R) / I(U) / I(D) is kept pressedfor a second or more.2. Light Control Setting (ALC)2-1. ALC Mode with SUPER-D2 ONSuper Dynamic2 Function (SUPER-D2)The important object in a scene is usually placed in the center of the monitor screen. In the SUPER-D2 mode, more photometric weight is given to the center of the screen (where the important objectis located) than to the edge of the screen (where a bright backlight would most likely be located).The SUPER-D2 function eliminates interference by strong background lighting which makes thecamera picture dark, such as a spotlight.1. Move the cursor to ALC and press I(S). The ALC CONT menu appears.2. Move the cursor to SUPER-D2 and select ON.3. If you want to adjust the video output level,move the "I" cursor for LEVEL. Adjust to thedesired level by pressing I(L) or I(R).(To be continued reverse page)SETTING PROCEDURES** ALC CONT **BACK LIGHT COMPSUPER-D2 ONLEVEL ..I......- +RET ENDWV-CW474AHighlighted0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ().,'":;&#!?=+-*/%$ÄÜÖÆÑÅSPACEPOSI RET END RESET................Character CursorPointerCharacterAreaCommandEditingAreaCAMERA ID menuCaution:Connect to 12 V DC (10.5 - 16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Makesure to connect the grounding lead to the GND terminal when the power is supplied from a24 V AC power source.q Panning tableAdjusts the panning angle of the camera.w Pan lock screwFixes the panning position.e Tilting lock screwFixes the tilting position.r AZIMUTH (Angle adjuster)Shoots in a straight-angle field of view when aiming at an object in a slanting direction even ifthe tilt angle has been set.t Zoom lock leverFixes the zoom position.y Focus lock leverFixes the focus position.u LEFT button (I) (L)Moves the cursor to the left, selects the mode and adjusts some levels.i RIGHT button (I) (R)Moves the cursor to the right, selects the mode and adjusts some levels.o UP button (I) (U)Moves the cursor upward and selects items in the CAM SET UP menu.!0 DOWN button (I) (D)Moves the cursor downward and selects items in the CAM SET UP menu.!1 SET button (I) (S)Activates an item selected in the CAM SET UP menu.!2 BW AUTO1 LEVEL switch (SW5)Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting is HIGH.!3 BW switch (SW4)Switches to AUTO1 between colour and black-and-white picture in response to light input. Thefactory default setting is OFF.!4 AP gain switch (SW3)Selects the aperture gain level to SHARP or SOFT. The factory default setting is SHARP.!5 UPSIDE DOWN switch (SW2)Turns the picture upside down by selecting ON. The factory default setting is OFF.!6 Sync switch (SW1)Switches internal sync (INT) mode or line-lock (LL) mode. The factory default setting is INT.LL: Line-lock mode is driven by 24 V AC or 220 V - 240 V AC.!7 Monitor output Jack (3.5 mm in Diam. mini jack)Connects the LCD monitor and such devices with 3.5 mm in diam. 2-pole L-type plug for check-ing images.!8 Optional heater connector DC outWhen an optional heater unit is installed in the camera, the harness exiting from the unit will beconnected to this.@3@2@5@1!9@0BrownBlueGreen/yellowBlackGrey!9-1!9-2!9-3@4!9-1 Camera power cable for WV-CW474AFE (24 V AC 50 Hz or 12 V DC)1. CAMERA SETUP MENUThis camera utilizes an on-screen user setup menu.• Opening the Setup MenuPress and hold down I(S) for 2 seconds ormore.The CAM SET UP menu appears on the monitor asshown at right.Check the current settings on the menu.Refer to the following sections for a detailed description of menu items. If you decide not to makeany changes after checking the current settings, move the cursor to END in the bottom line, andpress I(S) to close the setup menu.Note: If no button is pressed for 6 minutes while a setup menu is being displayed on the monitorscreen, it is automatically closed and the mode returns to the normal camera picture.2. SETUP OPERATIONThis camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SETUP menu, use the following buttons on the SW board.Left Button (I) (L): Moves the cursor to the left. Use this button to select or adjust the parame-ters of the selected item. The parameter changes each time this button ispressed.Right Button (I) (R): Moves the cursor to the right. Use this button to select or adjust the para-meters of the selected item. The parameter changes each time this buttonis pressed.Up Button (I) (U): Moves the cursor upwards. Use this button to select an item or adjust theparameters.Down Button (I) (D): Moves the cursor downwards. Use this button to select an item or adjustthe parameters.Set Button (I) (S): Executes selections and displays a submenu for an item with the mark.• To reset the parameter to the factory default setting, move the cursor to the parameter to bereset and press I(L) and I(R) simultaneously.• To return to the previous menu or page, move the cursor to RET and press I(S).• To close the setup menu, move the cursor to END and press I(S).• All Reset OperationAll Reset allows you to reset all setup menu items to the factory default settings if you are unsureabout the correct settings. Proceed as follows:(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).(2) While pressing both I(L) and I(R), press I(S) for a few seconds. The message ALLRESET momentarily appears on the monitor screen.This resets all adjustments and parameters to the factory default settings except for the PIXOFF setting.• Editing the CAM SET UP MenuImportant Notice:When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannotchange the currently active settings. This is to prevent accidental changing of the settings.To edit the CAM SET UP menu (change settings), press I(U) and I(D) or I(L) and I(R) tomove the cursor to SET UP DISABLE in the bottom line.Press I(S). SETUP DISABLE changes toSETUP ENABLE. Move the cursor to DIP SW.Press I(S). DIP SW changes to MENU. Thenmove the cursor to the item(s) you want tochange.Notes:• When DIP SW is selected for CAM SET UPmenu, five modes can be set with the DIPswitches.• To operate the camera functions with the system controller, select MENU in the CAM SET UPmenu.Important Notice:When the setup menu is closed after changing the parameters in the menu, the new values arestored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). Thesevalues remain valid until new values are stored, even if the power of the camera is off. ↵** CAM SET UP **CAMERA ID OFFALC ALCSHUTTER ---AGC ON(HIGH)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFDIP SWEND SET UP DISABLE↵↵↵** CAM SET UP **CAMERA ID OFFALC ALCSHUTTER ---AGC ON(HIGH)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFMENUEND SET UP ENABLE↵↵↵↵↵SETUP↵↵↵↵** CAM SET UP **CAMERA ID OFFALC ALCSHUTTER ---AGC ON(HIGH)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFDIP SWEND SET UP DISABLE1. The following functions are built in.(1) Auto Light Control (ALC)(2) The SUPER-D2 function eliminates interference by strong background lighting whichmakes the camera picture dark, such as a spotlight.Dynamic range of 48 dB (Typ)(3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync(4) Auto/Manual White Balance Function(5) Electronic Shutter Function2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)3. Minimum illumination of 2.0 lx (0.20 footcandle) (WIDE) (Colour mode)Minimum illumination of 0.2 lx (0.02 footcandle) (WIDE) (Black-and-white mode)Minimum illumination of 0.8 lx (0.08 footcandle) (WIDE) with the WV-CW2SE optional domecover (Colour mode)Minimum illumination of 0.1 lx (0.01 footcandle) (WIDE) with the WV-CW2SE optional domecover (Black-and-white )4. 480 lines of horizontal resolution (Colour normal mode)510 lines of horizontal resolution (Colour High Resolution mode)570 lines of horizontal resolution (Black-and-white mode)5. High quality picture:(a) 2H type vertical enhancer for greater picture sharpness(b) Chroma averaging circuit for better colour signal-to-noise ratio(c) Minimum of aliasing on fine objects(d) Expanded dynamic range by use of knee circuit(e) Highlight aperture correction for greater picture detail of bright objects6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF7. Built-in Digital Motion Detector8. Auto black-and-white mode enables the camera to switch between colour and black-and-whitepicture in response to Light input.9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.FEATURES1. Do not attempt to disassemble the camera.To prevent electric shock, do not remove screws or covers.There are no user-serviceable parts inside. Ask qualified service personnel for servicing.2. Handle the camera with care.Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged byimproper handling or storage.3. The installation should be made by qualified service personnel or system installers.4. Do not use strong or abrasive detergents when cleaning the camera body.Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a milddetergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.5. Clean the lens with care.Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tippedapplicator and ethanol.PRECAUTIONSBefore attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.MAJOR OPERATING CONTROLS AND THEIR FUNCTIONSN0304-0 3TR002452AAA Printed in JapanPanasonic's WV-CW474AF/CW470AS series colour digital camera introduces a new level of highpicture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensorhaving 752 horizontal pixels (picture elements), and digital signal processing LSIs. This modeloffers cutting-edge technology for advanced video surveillance.PREFACEColour CCTV CamerasOperating InstructionsRemove: Transport protection screw (Red)Space for heater unittqrw Remove: Transport protection screw (Red)LEFTUPDOWNSETRIGHT LOWHIGHOFFAUTO1SHARPSOFTOFFONINTLLuio!0!1!2!3!4!5!6!7!8y eModel Nos. WV-CW474AFEWV-CW470AS!9-3 Camera power cable for WV-CW470AS (220 V - 240 V AC 50 Hz)Caution:Connect to 24 V AC (19.5 V-28 V) class 2 power supply only.@0 Video output cable with BNC connectorConnects with the video connector of the monitor.Caution:Before attempting to connect or operate thisproduct, please read the marking on the top.The serial number of this product may be found onthe top of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE. REFER SER-VICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRICSHOCK DO NOT OPEN FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXTCAREFULLY.WARNING: This apparatus must be earthed.IMPORTANTThe wires in this mains lead are coloured in accordance with thefollowing code.Green-and-yellow: EarthBlue: NeutralBrown: LiveAs the colours of the wire in the mains lead of this appliancemay not correspond with the coloured markings identifying the ter-minals in your plug, proceed as follows.The wire which is coloured green-and-yellow must be con-nected to the terminal in the plug which is marked with the letter Eor by the earth symbol I or coloured green or green-and-yellow.The wire which is coloured blue must be connected to the ter-minal in the plug which is marked with the letter N or colouredblack.The wire which is coloured brown must be connected to theterminal in the plug which is marked with the letter L or colouredred.The exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is interned to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons.Vi deklarerar härmed värt fulla ansvar för att den produkt tillvilken denna deklaration hänvisar är i överensstämmelse medstandarddokument, eller andra normativa dokument somframstölls i Direktiv 73/23/EEC och 89/ 336/EEC.Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämäilmoitus koskee, noudattaa seuraavia standardeja tai muitaohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EECia 89/336/EEC. säädöksiä.We declare under our sole responsibility that the product towhich this declaration relates is in conformity with the stan-dards or other normative documents following the provisions ofDirectives EEC/73/23 and EEC/89/336.Wij verklaren als enige aansprakelijke, dat het product waaropdeze verklaring betrekking heeft, voldoet aan de volgendenormen of andere normatiefve dokumenten, overeenkomstigde bepalingen van Richtlijnen 73/23/ EEC en 89/336/EEC.Vi erklærer os eneansvarlige for, at dette produkt, som dennedeklaration omhandler, er i overensstemmelse med denfølgende standarder eller andre normative dokumenter i følgebestemmelserne i direktivene 73/23/ EEC og 89/336/EEC.Vi erklærer oss alene ansvarlige for at produktet som denneerklæringen gjelder for, er i overensstemmelse med følgendenormer eller andre normgivende dokumenter som fælgerbestemmelsene i direktiven 73/23/ EEC og 89/336/EEC.Turn the power off at the mains todisconnect the main power for allunit.WARNING: All work related to the installation of this product should be made by qualified service personnel or sys-tem installers.CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorpo-rated in the electrical installation of the building.6. Never face the camera towards the sun.Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at thesun or other extremely bright objects. Otherwise, blooming or smear may be caused.7. Do not operate the camera beyond the specified temperature, humidity or power sourceratings.Use the camera at temperatures within –10 °C to +50 °C (–14°F - 122 °F), and humidity below 90%. The input power source for WV-CW474AFE is 24 V AC 50 Hz or 12 V DC and for WV-CW470AS is 220 V - 240 V AC 50 Hz.8. Turn the circuit breaker off which supplies the camera with the power when abnormalconditions are encountered.!99-2 Power cable for heater unit WV-CW3HE (24 V AC 50 Hz) (applicable only to WV-CW474AFE)Caution:Connect to 220 V - 240 V AC 50 Hz. The optional heater unit operates on 24 V AC that hasbeen supplied through the camera.@1111 Dome cover@2 Camera mounting bracketThe WV-CW470AS is supplied with a mounting bracket for ceiling installation.@3 Camera attachment@4 Cable access hole@5 Sideway cable exitThe model shown is WV-CW474AFE.

/ 2

Related manuals for Panasonic WV-CW470AS