Panasonic WV-CW244F Operating Instructions Manual

Also see for WV-CW244S: Specifications Specifications

Panasonic WV-CW244F Operating Instructions Manual Manual pdf 1 page image

!6!2!4!5!3!2 Dome cover!3 Video output cable with BNC connectorConnects with the video connector of themonitor.!4 Camera power cableSupplies 24 V AC or 12 V DC from an exter-nal power source.!5 Heater power cableSupplies 24 V AC from an external powersource to an optional heater.!6 Camera mounting bracketOnly WV-CW244S (surface mount type) issupplied with a mounting bracket for ceilinginstallation.■ Installation Plans & Preparations● WV-CW244F“F” stands for flash mounting. This model can be mounted on a two-gang junction box (4“ x 4“) pre-installed in the wall or ceiling.1. SpacePrepare a space larger than ø160 mm.2. Junction boxProcure and install a junction box that meets the dimensions in the figure.3. Camera Fixing ScrewsProcure four screws (M4) suitable for the junction box.4. Cable routeCables will go behind the junction box.5. Waterproof ProcessWhen necessary, apply waterproof process to the camera and relevant portions.Be sure to apply silicone rubber to the camera fixing screws in case of outdoor installation.INSTALLATIONCamera fixing screw x 4 (procured locally)46mm(1-13/16")83.5mm (3-5/16")● WV-CW244S“S” stands for surface mounting. This model can be installed on the surface of the wall or ceilingusing the supplied bracket.1. SpacePrepare a space larger than ø160 mm.2. Bracket Fixing ScrewsTo fix the bracket, procure four M4 screws suitable for the surface and structure of the wall/ceil-ing.3. Camera Fixing ScrewsFour screws are supplied as standard accessories.4. Cable route• When routing cables through the wall/ceiling, drill a hole as shown in the figure.• When routing cables sideway, open the sideway cable exit unscrewing the lid by use of a hexa-gon wrench. Screw the detached lid to the cable access hole on the bottom of the bracket.5. Waterproof ProcessWhen necessary, apply waterproof process to the camera and relevant portions.If you use camera fixing screws that are locally procured, be sure to apply silicone rubber to thescrews.85 mm(3-3/8")85 mm(3-3/8")51 mm(2")Camera fixing screw x 4 (supplied)Bracket fixing screw x 4(procured locally)Bracket centerCable access holefor 3/4" pipe2nd transportprotection screw2. Remove the two red-colored screws provid-ed for transport protection using a Philipsscrewdriver.■ Mounting the Camera● Disassembly of the camera1. Remove the dome cover by loosening threetamper-proof screws using the supplied bit.Color CCTV CameraOperating InstructionsModel No.WV-CW244FWV-CW244SBefore attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.N0803-1093 3TR001693BAA Printed in JapanPREFACEThe WV-CW244 series is a 1/3” CCD color cam-era designed for use in a video surveillancesystem. The camera features a high pictureThe exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is interned to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons.The serial number of this product may be found onthe top of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.SA 1966SA 1965WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, suchas vases, shall be placed on the apparatus.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE. REFER SER-VICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRICSHOCK DO NOT OPENNOTE: This equipment has been tested and foundto comply with the limits for a Class A digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference when theequipment is operated in a commercial environ-ment. This equipment generates, uses, and canradiate radio frequency energy and, if not installedand used in accordance with the instruction manu-al, may cause harmful interference to radio com-munications.Operation of this equipment in a residential area islikely to cause harmful interference in which casethe user will be required to correct the interferenceat his own expense.FCC Caution: To assure continued compliance,(example - use only shielded interface cables whenconnecting to computer or peripheral devices). Anychanges or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate this equipment.For U.S.Aquality thanks to the use of digital signal pro-cessing LSIs, and easy installation.1. This product should be installed and con-nected by qualified service personnel orsystem installers in conformity with NEC.2. Use a class 2 power source supplying 12 VDC or 24 V AC.3. To prevent fire or electric shock hazard, usea UL listed cable (VW-1, style 1007) to con-nect the power supply to the camera.4. Be sure to use a ceiling board/wall havingenough strength to support this camera.5. Handle the camera with care.Do not abuse the camera. Avoid striking,shaking, etc. The camera could be dam-aged by improper handling or storage.6. Do not use strong or abrasivedetergents.Use a dry cloth to clean the camera bodywhen dirty.In case the dirt is hard to remove, use amild detergent and wipe gently. Afterwards,wipe off the remaining detergent with a drycloth.7. Clean the lens faceplate with care.Do not clean the lens with strong or abra-sive detergents. Use lens tissue or a cottontipped applicator and ethanol.8. Never face the camera towards the sun.Do not aim the camera at bright objects.Whether the camera is in use or not, neveraim it at the sun or other extremely brightobjects. Otherwise, blooming or smear maybe caused.9. Do not operate the camera beyond itsspecifications.Use the camera under conditions wheretemperature is between –10 °C to +50 °C(14 °F to 122 °F), and humidity is below90 %. The input power source is 24 V AC or12 V DC.10. Use a monitor whose resolution is at leastequal to that of the camera.PRECAUTIONS• Mounting method: Flash mounting/WV-CW244F, Surface mounting/WV-CW244S• Signal processing: Automatic Light Control(ALC), Automatic Gain Control (AGC),Automatic Tracing White Balance (ATW),etc.• Synchronization: Internal, Line-Lock (only24 V AC), and Multiplexed Vertical Drive(VD2)• Minimum illumination: 2.4 lx (0.24 foot-can-dle) at WIDE• Signal-to-noise ratio: 50 dB (Equivalent toAGC OFF)• Horizontal resolution: 480 TV lines• Optional heater unit available for the cam-era used at temperatures between –10 ˚Cand –30 ˚C (14˚F and –22˚F).FEATURESMAJOR OPERATING CONTROLS AND THEIR FUNCTIONSq Focus lock leverFixes the focus position after adjusting.w Tilting lock screwFixes the tilting position after adjusting.e Zoom lock leverFixes the zoom position after adjusting.r Panning tableAdjusts the panning angle of the camera.t Azimuth adjusterAdjusts the azimuth angle to obtain a levelimage.y Pan lock screwFixes the panning position after adjusting.u Heater power connectorSupplies power to the optional heater unitwhen it is built in the camera. Connect herea harness sticking out from the heater unit.i Synchronization Mode SelectorSpecifies a source for synchronization.INT: Internal 2:1 interlace.LL: Line-lock mode driven by 24 V AC.The default setting is INT.Note: Do not set the switch to LL (Line-Lock) position when supplying 12 V DCto avoid synchronization error.o Back Light Compensation SelectorON: Compensates the background if it isbrighter than the object.OFF: Does not compensate.The default setting is OFF.!0 Aperture Level SelectorSHARP: Sharpens the image outline.SOFT: Softens the image outline.The default setting is SHARP.!1 Video jack (3.5-diam. mini jack)For connecting an LCD monitor to adjustthe camera images. Use an L-type plug tosave space.ON1 2 3OFF ONLLSYNC INT*OFF*BLC ONSOFTAP SHARP*2nd transport protection screw (Red)Space for heater unitq wertyuio!0!1This Class A digital apparatus complies with cana-dian ICES-003.Cet appareil numérique de la classe A estconforme à la norme NMB-003 du Canada.For Canada* Default setting

/ 2

Related manuals for Panasonic WV-CW244S