Panasonic TQBC0627-2 Operating Instructions Manual

Panasonic TQBC0627-2 Operating Instructions Manual Manual pdf 47 page image

47signal name horizontal vertical PCfrequency(kHz) frequency(Hz)1 640 × 400 @70 Hz 31.47 70.00 ∗2 640 × 480 @60 Hz 31.47 59.94 ∗3 Macintosh13” (640 × 480) 35.00 66.67 ∗4 640 × 480 @75 Hz 37.50 75.00 ∗5 852 × 480 @60 Hz 31.50 60.00 ∗6 800 × 600 @60 Hz 37.88 60.32 ∗7 800 × 600 @75 Hz 46.88 75.00 ∗8 800 × 600 @85 Hz 53.67 85.06 ∗9 Macintosh16” (832 × 624) 49.73 74.55 ∗10 1,024 × 768 @60 Hz 48.36 60.00 ∗11 1,024 × 768 @70 Hz 56.48 70.07 ∗12 1,024 × 768 @75 Hz 60.02 75.03 ∗13 1,024 × 768 @85 Hz 68.68 85.00 ∗14 Macintosh21” (1,152 × 870) 68.68 75.06 ∗15 1,280 × 1,024 @60 Hz 63.98 60.02 ∗16 1,280 × 1,024 @75 Hz 79.98 75.03 ∗17 1,280 × 1,024 @85 Hz 91.15 85.02 ∗18 1,600 × 1,200 @60 Hz 75.00 60.00 ∗ConnectionsPC Input Terminals connectionNotes:(1) Computer signals whichcan be input are those witha horizontal scanningfrequency of 15 to 110 kHzand vertical scanningfrequency of 48 to 120 Hz.(However, the image will notbe displayed properly if thesignals exceed 1,200 lines.)(2) The display resolution is a maximum of 640 × 480 dots when the aspect mode is set to “4:3”, and 852 × 480 dotswhen the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possibleto show fine detail with sufficient clarity.(3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible,you will need to make setting changes to the computer at the time of connection.(4) Some PC models cannot be connected to the set.(5) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.(6) The computer shown in the illustration is for example purposes only.(7) Additional equipment and cables shown are not supplied with this set.(8) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specifiedfrequency range.(9) Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.Signal Names for D-sub 15P ConnectorS VIDEOR - STANDBYG - POWER ON STR F TV/AVAV3VIDEO L R/ /S VIDEOAV3VIDEO L RCOMPUTERConversion adapter(if necessary)RGBD-sub 15pPC cableFerrite core (large size)(supplied)Less than4" (10 cm)Less than4" (10 cm)Applicable input signals for PC Input(D-sub 15P) (∗∗∗∗∗ Mark)Input signal that can be displayedPin No.12345Pin No.678910Pin No.1112131415Signal NameR (P R/CR)G (Y)B (P B /CB )NCGND (Ground)Signal NameGND (Ground)GND (Ground)GND (Ground)NC (not connected)GND (Ground)Signal NameNC (not connected)NCHD/SYNCVDNCPin Layout for PC Input Terminal167839451015 14 13 12 112Note: Signals without above specificationmay not be displayed properly.