Panasonic TH-80LF50W Operating Instructions Manual

Contents

Panasonic TH-80LF50W Operating Instructions Manual Manual pdf 46 page image

46Options AdjustmentsItem AdjustmentsButton lockOff On MENU&ENTEROff: All the buttons on main unit can be used.MENU&ENTER: Locks MENU and buttons on main unit.On: Locks all the button on main unit except the Power switch.Sets Button lock with the unit buttons in the following procedure.Off: Press + / four times→Press INPUT four times→Press - / four times→PressMENU&ENTER: Press four times→Press + / four times→Press INPUT four times→PressOn: Press - / four times→Press four times→Press + / four times→PressRemocon UserlevelOff User1 User2 User3Off: You can use all of the buttons on the remote control.User1: You can only use , , , , buttons on the remote control.User2: You can only use button on the remote control.User3: Locks all the buttons on remote control.Off-timer functionEnable: Enables the “Off-timer function”.Disable: Disables the “Off-timer function”.Note: When “Disable” is set, the Off-timer is cancelled.Initial Power ModeNormal On StandbySets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal: Power returns in as the same state as before the power interruption.Standby: Power returns in standby mode. (Power Indicator : red/orange)On: Power returns in power On. (Power Indicator : green)Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.Set value range: 0 - 100(Standard value: 0)Remote IDThe setting of this menu is valid only when using ID remote control.Off: Disables ID remote control functions. You can use normal remote control operations.On: Enable ID remote control functions.Note: To use the ID remote control function, it is necessary to set each ID number of remote control anddisplay unit. About the setting method, please refer to “ID Remote Control Function” (see page38) and “ID select” (above-mentioned).Serial IDSets the panel ID Control.Off: Disables external control by the ID.On: Enables the external control by the ID.Serial Daisy ChainSets the top and end of a daisy chain when the SERIAL terminal of Display is daisy chained.---: When the Display is under SERIAL control on a standalone basis, or if not at the top or end of daisy chain.Top: To connect to the top of daisy chain.End: To connect to the end of daisy chain.Studio W/BOff: Nullify all the settings adjusted.On: Sets the colour temperature for TV studio.Note: Valid only when the “Warm” is set as “White balance” in Picture menu.Slot powerOff Auto OnOff: Power is not transmitted to the slot power.Auto: Power is transmitted to the slot power only when main power is on.On: Power is transmitted to the slot power when main power is on or in the standby state.Note: In some cases, power is transmitted to the slot power when main power is on or in the standbystate regardless of the slot power setting.Power ON ScreenDelayOff 1 2 3.... 30You can set the power-on delay time of the displays to reduce the power load, when you press toturn on the multiple displays that are set together, for example, on MULTI DISPLAY system.Set each display’s setting individually.Off: The display will be turned on at the same time as is pressed.1 to 30 (sec.) : Set the power-on delay time (second).After pressing , the display will be powered on with time delay depending on this setting.Notes:• During this function is working, the power indicator is blinking green.• This function also works when the power recovers from failure or after plugging off and in again thepower cord.Clock DisplayOff: Not display the clock.On: Display the clock.The clock is displayed at the lower left of the screen when button is pressed.Note: When “PRESENT TIME Setup” is not set, the clock is not displayed evenif “Clock Display” is “On”. (see page 29)10:00