Panasonic TH-103PF12E Service Manual

Also see for TH-103PF12E: Specifications Operating instructions Service manual

Contents

Panasonic TH-103PF12E Service Manual Manual pdf 9 page image

9TH-103PF12E4 SpecificationsPower Source 220-240 V AC, 50/60HzPower ConsumptionPower on 1450 WStand-by condition Save OFF 1.2 W, Save ON 0.7 WPower off condition 0.4 WPlasma Display panel Drive method: AC type 103-inch,16:9 aspect ratioScreen size 2,269 mm (W) × 1,276 mm (H) × 2,603 mm (diagonal)(No. of pixels) 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]Operating conditionTemperature 0 °C - 40 °CHumidity 20 % - 80 %Applicable signalsScanning format 525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) /60i 60p 50i 50p 24p 25p 30p 24sF, 1250 (1080) / 50iPC signals VGA, SVGA, XGA, SXGAUXGA ..... (compressed)Horizontal scanning frequency 15 - 110 kHzVertical scanning frequency 48 - 120 HzConnection terminalsDVI-D IN Video Input DVI-D 24 Pin × 1compliance with DVI Revision 1.0Audio Input Stereo mini jack (M3) × 10.5 VrmsContent Protection Compatible with HDCP 1.1LAN RJ45 10BASE-T / 100BASE-TX, compatible with PJLinkTMCOMPONENT / RGB IN Y / G (BNC) with sync 1.0 Vp-p (75-ohm)PB /B (BNC), PR /R (BNC) 0.7 Vp-p (75-ohm)Audio Input Stereo mini jack (M3) × 10.5 VrmsPC IN (HIGH-DENSITY Mini-D-SUB 15PIN) Y or G with sync 1.0 Vp-p (75-ohm)Y or G without sync 0.7 Vp-p (75-ohm)B / P B / C B : 0.7 Vp-p (75-ohm)R / P R / CR : 0.7 Vp-p (75-ohm)HD / VD: 1.0 - 5.0 Vp-p (high impedance)VBS (use HD port) with picture 1.0 Vp-p (high impedance)without picture 0.3 Vp-p (high impedance)Audio Input Stereo mini jack (M3) × 10.5 VrmsSERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLEAUDIO OUT RCA PIN JACK × 2 (L / R)OUTPUT LEVEL : VARIABLE (- - 0 dB) [INPUT 1KHz / 0dB, 10Kohm Load]Accessories SuppliedRemote Control Transmit-terEUR7636090RBatteries R6 Size × 2Fixing band TMME203 × 2Ferrite core J0KG00000146 (Set of 2)Noise cut filter TXZDM011MBEDimensions (W × H × D) 2,412 mm × 1,419 mm × 129 mm (141 mm when including protruding portion of slots)Mass (weight) approx. 201.0 kg netNote:• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.• This equipment complies with the EMC standards listed below.EN55022, EN55024, EN61000-3-2, EN61000-3-3.