Panasonic FZ-10 Series Instruction Manual

Also see for FZ-10: Operating instructions Operating instructions Service manual

FUNCTIONAL DESCRIPTION1Description FunctionFiber lock leverԘPower indicator (Green)ԙ Lights up when the power is ON,blinks during auto-teaching.Both blink alternatelywhen a manual-teachingerror occurs.Both blink simultaneous-ly when the output isshort-circuited.Setting mode selection switchԜOutput operation mode switchԝOperation indicator (Red)ԚLocks or unlocks fiber cables.Lights up when the output is ON.The teaching button is ineffective if the switch is set on 'LOCK',but is effective if the switch is set on 'SET'.Teaching protect switchԛManual-teaching is selected if the switch is set on 'MANUAL'.Auto-teaching is selected if the switch is set on 'AUTO'.Coincident-ON is selected if the switch is set on 'NORMAL'.Incoincident-ON is selected if the switch is set on 'INVERSE'.Timer operation mode switchԞ The OFF-delay timer is ineffective if the switch is set on 'NON',but is effective if the switch is set on 'OFD'.Tolerance adjusterԟ Determines the tolerance of equivalence, with respect to thereference color that the sensor has been taught, in 16 grades.Teaching buttonԠTeaches the sensor the target color as the criterion (referencecolor.)While the button is held, the sensor emits blue, red, andgreen beams one after the other.146104812TOLERANCEJAPANFZÐ11NONOFDNORMALINVERSEMANUALAUTOSETLOCKOUTPOWERTEACHFINENONOFDNORMALINVERSEMANUALAUTOSETLOCKԘ Fiber lock leverԙ Power indicator(Green)Ԛ Operation indicator (Red)Ԡ Teaching buttonԛ Teaching protectswitchԜ Setting modeselection switchԝ Output operationmode switchԞ Timer operationmode switchԟ Tolerance adjusterSETTING41.࡮Setting reference colorPrepare a sample object bearing the target color you want to detect.Choose manual teaching or auto-teaching.࡮ Teaching the reference color on a stationary object.Ԙ Set the tolerance adjuster at the 16th grade(ً mark) with the adjusting screwdriver.ԙԚSet the teaching protect switch on 'SET'.Set the setting mode selection switch on'MANUAL'.٨ Procedure٨٨During teaching, the FZ-10 series resolves the color projected by thespot into red, green, and blue components which are processed as nu-merical values and stored into the EEPROM memory. If, during teaching,the spot area is not filled by one uniform color, such aswhen the target objects are smaller than the spot area,or are partly projected upon, then colors other than theone you want to detect may also be sensed. Make surethat objects fill the whole spot area during teaching, aswell as, sensing.The taught data is saved in the EEPROM even when the sensor powersupply is switched off. However, the guaranteed rewrite operations arelimited to 100,000 times because of its lifetime.To manipulate the DIP switches, use a pair of tweezers, etc., with a tipwidth of 0.8mm approx.Emitting spotWorkpiece1Setting referencecolorINVERSE NORMAL2Setting outputoperationOFD NON3Setting timeroperation146104812FINE4Setting toleranceSetting by manual-teaching146104812FINEMANUALAUTOSETLOCKTeaching protectswitchSetting modeselection switchThank you very much for purchasing Panasonic products. Read this Instruc-tion Manual carefully and thoroughly for the correct and optimum use of thisproduct. Kindly keep this manual in a convenient place for quick reference.٨٨Never use this product as a sensing device for personnel pro-tection.In case of using sensing devices for personnel protection, useproducts which meet laws and standards, such as OSHA, AN-SI or IEC etc., for personnel protection applicable in each re-gion or country.WARNINGI/O CIRCUIT DIAGRAMS3٨ PNP output type / FZ-11P٨ NPN output type / FZ-11Symbols ... DZ DTr: Reverse supply polarity protection diode: Surge absorption zener diode: NPN output transistorSymbols ... DZ DTr: Reverse supply polarity protection diode: Surge absorption zener diode: PNP output transistorDTrZDLoad(Black) Output(Blue) 0V(Brown) +V+-12 to 24V DCr10%Color codeInternal circuit Users' circuit100mA max.Sensor circuitDTr ZDLoad(Black) Output(Blue) 0V(Brown) +V+-12 to 24V DCr10%100mA max.Color codeInternal circuit Users' circuitSensor circuitMOUNTING2ԘޓԙFit the rear part of the amplifier on the attachedamplifier mounting bracket (MS-DIN-3) or a35mm width DIN rail.Press down the front part of the amplifier on theamplifier mounting bracket (MS-DIN-3) or the35mm width DIN rail to fit it.How to mount the amplifierԘԙPush the amplifier forward.Lift up the front part of the amplifier to remove it.How to remove the amplifierHow to connect the fiber cablesNotes: 1)2)The fiber heads of the FD-L51 and / or the FD-L52 and / or the FD-L53 and/ or the FD-L54 can be closely mounted together as long as their spots donot overlap each other.Refer to the fiber's Instruction Manual for the fiber tip fitting method.ԘԙAttached amplifier mountingbracket or 35mm width DIN rail.ԘԙԘԙԚFiber lockleverFiber cableBeam-emittingpartBeam-receiving partTag markNote: Please take care that if the front part is lifted without pushing the amplifier for-wards, the hooks on the rear portion of the mounting section are likely to break.ԘԙԚUnlock the fiber lock lever by lower-ing it.Insert the beam-emitting fiber cabletagged with the mark 'ޓ' into thebeam-emitting part 'P', and thebeam-receiving fiber cable into thebeam-receiving part 'D'. They shouldbe inserted gradually until the posi-tion where they stop. If the emittingfiber cable and the receiving fibercable are reversely inserted, properoperation cannot be obtained.Lock the fiber lock lever to the origi-nal position.FZ-10 SeriesColor Detection Fiber Sensor AmplifierINSTRUCTION MANUALRugghölzli 2CH - 5453 BusslingenTel. +41 (0)56 222 38 18Fax +41 (0)56 222 10 12mailbox@sentronic.comwww.sentronic.comProdukte, Support und ServiceSENTRONIC AG

/ 3

Related manuals for Panasonic FZ-10