Panasonic CT-27HL15 Operating Instructions Manual

Also see for CT-27HC15: Manual

Contents

Panasonic CT-27HL15 Operating Instructions Manual Manual pdf 46 page image

REMOTE CONTROL OPERATION / OPERACIÓN DEL CONTROL REMOTO / F ONCTIONNEMENT DE LA TÉLÉCOMMANDERemoteRemotoTélécommandeProgramming The Remote ControlProgramación del Control RemotoProgrammation de la télécommandeThe Universal Remote Control can be programmed tooperate many manufacturers’ components, using thecomponent function buttons for VCR, DVD, CABLE orDBS. Follow the procedures for programming your RemoteControl with or without a code for the component.El Control Remoto Universal puede programarse paraoperar componentes de varios fabricantes usando losbotones de función para VCR, DVD, CABLE o DBS.Siga los procedimientos para programar su ControlRemoto con o sin código para el componente.La télécommande universelle peut être programmée pourcommander le fonctionnement d'appareils d'autresmarques à l'aide des touches de fonctions VCR, DVD,CABLE, ou DBS. Suivre l'une des procédures deprogrammation données ci-dessous.Note: Determine the manufacturer of the component and look in thetable for the code.Nota: Determine el fabricante del componente y busque en latabla su código.Nota: Noter la marque de l'appareil et identifier le code dans letableau des codes.English Procedures1. Confirm that the external component is plugged in andoperating.2. Turn the component off.3. Press and together, for at least 5seconds. After 5 seconds, the illuminated mode(component) buttons will begin to flash. Release theACTION and POWER buttons.4. Press appropriate component button on the RemoteControl: VCR, DVD, CABLE or DBS. The componentbutton will illuminate steadily and all others will go out.5. Enter the 3-digit component code using the RemoteControl numeric keypad (0 ~ 9 buttons). The componentbutton will blink twice.6. Press the Remote Control to test thecomponent. If the procedure was successful, thecomponent will turn on and the component key will blinktwice and then go out.Note: If the component does not operate with the Remote Control,repeat steps 3 through 6 using another code (some brandshave multiple codes). If an incorrect code is entered, or if theprocedure takes longer than 30 seconds, the programming willfail.Programming Without A CodeThis procedure searches all codes and is called the“sequence method.”1. Confirm that the external component is plugged in andon.2. Turn the component off.3. Press and together, for at least 5seconds. After 5 seconds, the illuminated mode(component) buttons will begin to flash. Release theACTION and POWER buttons.4. Press the appropriate component button on the RemoteControl. The component button will illuminate steadilyand all others will go out.5. Press the button to set the remote control intothe step mode.6. Point the remote control towards the component.7. Press VOL X (the mode key will blink three times), thenpress the Remote Control button to test thecomponent. Continue this process until the proper codeis found. If the procedure was successful, the componentwill turn on.Note: Each time you press the VOL X button, make sure that thecomponent key blinks twice before pressing the POWERbutton.8. Once the device responds, press to store thecode. The mode (component) button will blink twice.Note: It may take many attempts before the correct code is found. Ifyou miss a code, press W VOL, then press thebutton to test the component.Procedimiento Español1. Confirme que el componente esté conectado y enoperación.2. Apague el componente.3. Presione los botones de y juntos,cuando menos 5 segundos. Después de este tiempo,los botones de componentes comenzarán a destellar.Desoprima los botones ACTION y POWER.4. Presione el botón de la función apropiada delcomponente en el Control Remoto. (VCR, DVD, CABLEo DBS). El botón seleccionado quedará iluminado y elresto se apagará.5. Accese el código del componente de 3 dígitos usando elteclado numérico (botones 0 ~ 9) del Control Remoto. Elbotón del componente destellará dos veces.6. Presione el botón de el Control Remoto paraprobar el componente. Si éste procedimiento ha sidoexitoso, el componente se encenderá.DeviceEquipoAppareilOperatesFuncionaContrôleDefaultRéglage par défautTVTelevisiónTéléviseurPanasonic OnlySolo PanasonicPanasonic seulementPanasonic CodeCódigo TV PanasonicCodes PanasonicVCRVideocaseteraMagnétoscopeVCR (Preset)Videocasetera (predefinido)Magnétoscope ( Préréglé)Panasonic CodeCódigo PanasonicCodes PanasonicDBS/CBL DBS STB & CBL STB(Preset/predefinido Préréglé)Panasonic DBS CodeCódigo Panasonic DBSCodes DBS PanasonicDVDLecteur DVDDVD (Preset)DVD/disco Compacto(predefinido)Lecteur DVD et CD (Préréglé)Panasonic CodeCódigo PanasonicCodes PanasonicACTIONPOWERPOWERACTIONPOWERPOWERPOWERACTIONPOWERACTION POWERPOWER