Panasonic CQ-C1001NW Operating Instructions Manual

Also see for CQ-C1001NW: Installation instructions

AccessoriesOperating Instructions(English : YFM284C454ZA)(Deutsch : YFM284C455ZA)(Français : YFM284C456ZA)(Nederlands : YFM284C457ZA)(Svenska : YFM284C458ZA)(Italiano : YFM284C459ZA)(Español : YFM284C460ZA)(Dansk : YFM284C461ZA)Q'ty: 1 setInstallation Instructions(English, Deutsch, Français,Nederlands : YFM284C466ZA)(Svenska, Italiano, Español,Dansk : YFM284C467ZA)Q'ty: 1 setWarranty CardQ'ty: 1Lock Cancel Plate(FX0214C385ZA)Q'ty: 2Mounting Bolt(YEJV014C002N)Q'ty: 1Mounting Collar(FX0214C384ZA)Q'ty: 1Trim Plate(YFC054C079ZA)Q'ty: 1Power Connector(YEAJ02874)Q'ty: 1Notes:¡ The number in parentheses underneatheach accessory part name is the partnumber for maintenance and service.¡ Accessories and their part numbers aresubject to modification without priornotice due to improvements.¡ Mounting Collar and Trim Plate aremounted on the main unit at shipment.CD Player/ReceiverCQ-C1021NW/C1011NW/C1001NWOperating Instructions¡Please read these instructions carefully before using this product and keep this manual for future reference.CQ-C1021NMUTE/SQ RANDOM SCAN REPEAT TAVOLUMETUNE/TRACKREGMONOLOCBAND1 2 3 4 5 6PWR CTSRC DISPAPMD·MD·MSELSELSELPTYAF(CQ-C1021NW)SpecificationsYFM284C454ZC TAMACO1004-2055 Printed in ChinaGeneralPower Supply : 12 V DC (11 V – 16 V), NegativeGroundTone Controls (Bass) : ±12 dB (100 Hz)Tone Controls (Treble) : ±12 dB (10 kHz)Current Consumption : Less than 2.5 A (CD mode, 0.5 W4 channels)Maximum Power Output : 45 W x 4 (4 Ω)Speaker Impedance : 4 – 8 ΩPre-Amp Output Voltage : 2.5 V (CD mode, 1 kHz, 0 dB)Pre-Amp Output Impedance : 200 ΩDimensions (Main Unit) : 178(W) x 50(H) x 160(D) mmWeight (Main Unit) : 1.3 kgCD PlayerSampling frequency : 8 times oversamplingDA converter : 1 bit DAC SystemPick-up type : Astigma 3-beamLight source : Semiconductor laserWave length : 790 nmFrequency response : 20 Hz – 20 kHz (±1 dB)Signal to noise ratio : 96 dBTotal harmonic distortion : 0.01 % (1 kHz)Wow and flutter : Below measurable limitsChannel separation : 75 dBFM Stereo RadioFrequency Range : 87.5 MHz – 108 MHzUsable Sensitivity : 6 dB/μV (S/N 30 dB)Stereo Separation : 35 dB (1 kHz)AM (MW) RadioFrequency Range : 531 kHz – 1 602 kHzUsable Sensitivity : 28 dB/μV (S/N 20 dB)AM (LW) RadioFrequency Range : 153 kHz – 279 kHzUsable Sensitivity : 32 dB/μV (S/N 20 dB)Notes:¡ Specifications and design are subject to modification withoutnotice due to improvements.¡ Some figures and illustrations on this manual may be differentfrom real ones.Matsushita Electric Industrial Co., Ltd.Web Site: http://www.panasonic.co.jp/global/EnglishBefore Reading These InstructionsPanasonic welcomes you to our constantly growing family of electronic products owners.We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, andassembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours ofenjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.Laser Product Differences among 3modelsThis operating instruction manual is for 3 models CQ-C1021NW, CQ-C1011NW and CQ-C1001NW. All illustrations throughoutthis manual represent model CQ-C1021NW unless otherwise specified. The following table describes the differences among 3models.Label Indications and Their LocationsCAUTIONLASER RADIATION WHEN OPEN. DO NOT STAREINTO BEAM.CautionThis product utilizes a laser.Use of controls or adjustments or performance ofprocedures other than those specified herein mayresult in hazardous radiation exposure.Do not take apart this unit or attempt tomake any changes yourself.This unit is a very intricate device that uses a laserpickup to retrieve information from the surface ofcompact discs. The laser is carefully shielded so thatits rays remain inside the cabinet.Therefore, never try to disassemble the player or alterany of its parts since you may be exposed to laserrays and dangerous voltages.CLASS 1 LASER PRODUCTCaution LabelDeck Ass’y (in the unit,upper side)PreparationThe 24-hour system is used for the clock.Notes:¡ Adjust the clock when “NO CT” appears on the dis-play.¡ When a broadcast of FM Radio Data System isreceived, the clock is set automatically by the CT(Clock Time) service.¡ Hold down []] or [[] to change numbers rapidly.1 Select the radio AM mode.(a “Radio (AM [LW/MW]/FM)”)2 Hold down [DISP] (CT) for more than 2seconds.Hour blinks3 Adjust the hour.Hour entered[[]: sets the hour ahead.[]]: sets the hour back.4 Press [DISP] (CT).Minute blinks5 Adjust the minute.Minute entered[[]: sets the minute ahead.[]]: sets the minute back.6 Press [DISP] (CT).CompletedClock SettingFeatures Models CQ-C1021NW CQ-C1011NW CQ-C1001NWDisplay colour Blue Black BlackKey/disc slot illumination colour Red Red GreenMaintenanceYour product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routineexterior cleaning. Never use benzine, thinner, or other solvents.Cleaning theUnitFuseAnti-Theft SystemThis unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.Removing1 Turn off the power.2 Press [ ]. The face plate will open.3 Pull it out toward you.Mounting1 Slide the left side of the face plate inplace.2 Press the right end of face plate until a“click” is heard.Caution¡ This face plate is not waterproof. Do not expose it towater or excessive moisture.¡ Do not remove the face plate while driving your car.¡ Do not place the face plate on the dashboard or nearbyareas where the temperature rises high.¡ Do not touch the contacts on the face plate and themain unit, since this may result in poor electrical con-tact.¡ If dirt or other foreign substances get on the contacts,wipe them off with a clean and dry cloth.Face Plate Removing/Mounting(Anti-Theft System)If the replaced fuse fails, contact your nearest authorized Panasonic Service Centre.Warning¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unitdirectly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest author-ized Panasonic Service Centre.TroubleshootingTrouble Check pointNo power● Start the engine. (Or turn the ignitionswitch to the ACC position.)● Verify the wiring. (Ex. battery lead,power lead, ground lead, etc.)● Fuse blown (Contact the nearestPanasonic Service Centre.)● Ask a professional for fuse replace-ment.● Be sure to use the same rated fuse.No sound● Disable the mute function.● Verify the wiring.● Wait until the dew disappears beforeturning on the unit.Noise ● Make sure that grounding is establishedproperly.CommonFrequentnoise● Tune into another station of high-inten-sity waves.● Make sure that the antenna mountedpoint is grounded properly.RadioPreset datadeleted● The preset memory is cleared to returnto the original factory setting when thepower connector or battery is discon-nected.No sound, or discis automaticallyejected● Load the disc correctly.● Clean the disc.Disc PlayerSound skip,poor soundquality● Clean the disc.Sound skipdue tovibration● The maximum permissible tilt angle is30°.● Secure the unit.Disc notejectable● Press [u]. If the disc is still not eject-ed, contact the nearest PanasonicService Centre.No sound fromleft, right, front,or rear speaker● Adjust the balance and fader.● Verify the wiring.Trouble Check pointLeft and rightsounds arereversed● Connect the speaker lead correctly.Error Display Messages(The disc is ejected automatically.)The disc is dirty, or is upside down.The disc has scratches.● Check the disc.No operation by some cause.● If normal operation is not restored, callthe store where you purchased the unitor the nearest Panasonic ServiceCentre to ask for repairs.If You Suspect Something WrongCheck and take steps as described below.If the described suggestions do not solve the problem, it is recom-mended to take the unit to your nearest authorized Panasonic ServiceCentre. The product should be serviced only by qualified personnel.Please refer the checking and the repair to professionals. Panasonicshall not be liable for any accidents arising out of neglect of checkingthe unit or your own repair after your checking.Warning¡ Do not use the unit in an irregular condition, for example, with-out sound, or with smoke or a foul smell, which can causeignition or electric shock. Immediately stop using the unit andconsult your dealer.¡ Never try to repair the unit by yourself because it is dangerousto do so.21 21Safety InformationWarningObserve the following warnings when using thisunit.❑ The driver should neither watch the display nor operatethe system while driving.Watching the display or operating the system will distract the driv-er from looking ahead of the vehicle and can cause accidents.Always stop the vehicle in a safe location and use the parkingbrake before watching the display or operating the system.❑ Use the proper power supply.This product is designed for operation with a negative grounded12 V DC battery system. Never operate this product with other bat-tery systems, especially a 24 V DC battery system.❑ Protect the Deck Mechanism.Do not insert any foreign objects into the slot of this unit.❑ Do not disassemble or modify the unit.Do not disassemble, modify the unit or attempt to repair the prod-uct yourself. If the product needs to be repaired, consult yourdealer or an authorized Panasonic Service Centre.❑ Do not use the unit when it is out of order.If the unit is out of order (no power, no sound) or in an abnormalstate (has foreign objects in it, is exposed to water, is smoking, orsmells), turn it off immediately and consult your dealer.❑ Refer fuse replacement to qualified service personnel.When the fuse burns out, eliminate the cause and have it replacedwith the fuse prescribed for this unit by a qualified service engi-neer. Incorrect replacement of the fuse may lead to smoke, fire,and damage to the product.Observe the following warnings when installing.❑ Disconnect the lead from the negative (–) battery termi-nal before installation.Wiring and installation with the negative (–) battery terminal con-nected may cause electrical shock and injury due to a short circuit.Some cars equipped with the electrical safety system have specificprocedures of battery terminal disconnection.FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THEUNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEMRESULTING IN DAMAGE TO THE VEHICLE AND PERSONALINJURY OR DEATH.❑ Never use safety-related components for installation,grounding, and other such functions.Do not use safety-related vehicle components (fuel tank, brake,suspension, steering wheel, pedals, airbag, etc.) for wiring or fix-ing the product or its accessories.❑ Installing the product on the air bag cover or in a locationwhere it interferes with airbag operation is prohibited.❑ Check for piping, gasoline tank, electric wiring, and otheritems before installing the product.If you need to open a hole in the vehicle chassis to attach or wirethe product, first check where the wire harness, gasoline tank, andelectric wiring are located. Then open the hole from outside if pos-sible.❑ Never install the product in a location where it interfereswith your field of vision.❑ Never have the power cord branched to supply otherequipment with power.❑ After installation and wiring, you should check the nor-mal operation of other electrical equipment.The continuation of their using in abnormal conditions may causefire, electrical shock or a traffic accident.❑ In the case of installation to an airbag-equipping car,confirm warnings and cautions of the vehicle manufactur-er before installation.❑ Make sure the leads do not interfere with driving or get-ting in and out of the vehicle.❑ Insulate all exposed wires to prevent short circuiting.CautionObserve the following cautions when using thisunit.❑ Keep the sound volume at an appropriate level.Keep the volume level low enough to be aware of road and trafficconditions while driving.❑ This unit is designed for use exclusively in automo-biles.❑ Do not operate the unit for a prolonged period with theengine turned off.Operating the audio system for a long period of time with theengine turned off will drain the battery.❑ Do not expose the unit to direct sunlight or excessiveheat.Otherwise these will raise the interior temperature of the unit,and it may lead to smoke, fire, or other damage to the unit.❑ Do not use the product where it is exposed to water,moisture, or dust.Exposure of the unit to water, moisture, or dust may lead tosmoke, fire, or other damage to the unit. Make especially surethat the unit does not get wet in car washes or on rainy days.Observe the following cautions when installing.❑ Refer wiring and installation to qualified service per-sonnel.Installation of this unit requires special skills and experience. Formaximum safety, have it installed by your dealer. Panasonic isnot liable for any problems resulting from your own installationof the unit.❑ Follow the instructions to install and wire the product.Not following the instructions to properly install and wire theproduct could cause an accident or fire.❑ Take care not to damage the leads.When wiring, take care not to damage the leads. Prevent themfrom getting caught in the vehicle chassis, screws, and movingparts such as seat rails. Do not scratch, pull, bend or twist theleads. Do not run them near heat sources or place heavy objectson them. If leads must be run over sharp metal edges, protectthe leads by winding them with vinyl tape or similar protection.❑ Use the designated parts and tools for installation.Use the supplied or designated parts and appropriate tools toinstall the product. The use of parts other than those supplied ordesignated may result in internal damage to the unit. Faultyinstallation may lead to an accident, a malfunction or fire.❑ Do not block the air vent or the cooling plate of the unit.Blocking these parts will cause the interior of the unit to over-heat and will result in fire or other damage.❑ Do not install the product where it is exposed to strongvibrations or is unstable.Avoid slanted or strongly curved surfaces for installation. If theinstallation is not stable, the unit may fall down while driving andthis can lead to an accident or injury.❑ Installation AngleThe product should be installed in a horizontal position with thefront end up at a convenient angle, but not more than 30˚.The user should bear in mind that in some areas there may berestrictions on how and where this unit must be installed.Consult your dealer for further details.❑ Wear gloves for safety. Make sure that wiring is com-pleted before installation.❑ To prevent damage to the unit, do not connect thepower connector until the whole wiring is completed.❑ Do not connect more than one speaker to one set ofspeaker leads. (except for connecting to a tweeter)This pictograph intends to alert you to the presence ofimportant operating instructions and installation instruc-tions. Failure to heed the instructions may result insevere injury or death.■ Read the operating instructions for the unit and all other compo-nents of your car audio system carefully before using the system.They contain instructions about how to use the system in a safe andeffective manner. Panasonic assumes no responsibility for any prob-lems resulting from failure to observe the instructions given in thismanual.■ This manual uses pictographs to show you how to use the productsafely and to alert you to potential dangers resulting from improperconnections and operations. The meanings of the pictographs areexplained below. It is important that you fully understand the mean-ings of the pictographs in order to use this manual and the systemproperly.WarningThis pictograph intends to alert you to the presence ofimportant operating instructions and installation instruc-tions. Failure to heed the instructions may result ininjury or material damage.CautionSales and Support InformationFor UK and Ireland customers only.Customer Care Centre¡ For customers within the UK: 08705 357357¡ For customers within the Republic of Ireland: 01 289 8333¡ Visit our website for product information¡ E-mail: customer.care@panasonic.co.ukDirect Sales at Panasonic UK¡ Order accessories and consumable items for your productwith ease and confidence by phoning our Customer CareCentre Monday - Thursday 9:00am - 5:30pm, Friday9:30am - 5:30pm. (Excluding public holidays).¡ Or go on line through our Internet Accessory orderingapplication at www.panasonic.co.uk.¡ Most major credit and debit cards accepted.¡ All enquiries, transactions and distribution facilities areprovided directly by Panasonic UK Ltd.¡ It couldn't be simpler!¡ Also available through our Internet is direct shopping for awide range of finished products, so take a browse on ourwebsite for further details.VAROITUS – LASER-SÄTEILYVAARAAVATTAESSA. VAROALTISTUMISTASÄTEELLE.FÖRSIKTIGHET –LASERSTRÅLNING IÖPPNAT LÄGE. UNDVIKATT UTSÄTTAS FÖRSTRÅLEN.ADVARSEL – LASER-STRÅLING. UNNGÅEKSPONERING FORSTRÅLEN VED ÅPNING.ÇçàåÄçàÖ – ãÄáÖêçéÖàáãìóÖçàÖ èêàéíäêõíàà. àáÅÖÜÄíúÇéáÑÖâëíÇàü ãÄáÖêçéÉéàáãìóÖçàü.CAUTION - LASER RA-DIATION WHEN OPEN.AVOID EXPOSURE TOBEAM.VORSICHT - LASER-STRAHLUNG, WENNGEÖFFNET. VERMEIDENSIE EIN AUSSETZENGEGENÜBER DEMLASERSTRAHL.ATTENTION –RAYONNEMENT LASERSI OUVERT, ÉVITERTOUTE EXPOSITION AUFAISCEAU.ADVARSEL – LASERUDSENDES NÅR DERER ÅBNET. UNDGÅUDSÆTTELSE FORSTRÅLER.

/ 4

Related manuals for Panasonic CQ-C1001NW