Panasonic BB-HCM715A Installation Manual

Also see for BB-HCM715: Comparison chart Setup guide

Contents

Panasonic BB-HCM715A Installation Manual Manual pdf 4 page image

4Ceiling/Wall MountWiring without making a hole for a cable in the ceiling or wallFor BB-HCM735:Before following the procedures below, we recommend passing all cables (ACadaptor, LAN, audio/video, etc.) through a duct (i.e., hose, tube, etc.) forproper waterproofing.1. Secure the safety wire to the camera using screw A (included) andwasher S (included).• Make sure you attach the safety wire when mounting the camera, to prevent the camerafrom falling.2. Remove the tab on the flexible stand. Then pass the cables through thenotch.3. For BB-HCM715:Connect all necessary cables (AC adaptor, LAN, audio/video, etc.). Thenskip to step 7.For BB-HCM735:Pass the cables through the connector cover, and then connect allnecessary cables (AC adaptor, LAN, audio/video, etc.).Attach the connector cover by fastening the two screws.4. Attach the sunshade by fastening the two screws.5. Wrap the cables in the included foam strip and insert the foam strip intothe opening of the connector cover.• Leave about 10 mm (3/8 inches) of the foam exposed, as shown.6. Wrap the first 20 cm (7 7/8 inches) of the cables (starting with theconnector cover) using the included self bonding tape. Make sure to wrapthe opening of the connector cover thoroughly (three or four times).• Stretch the tape to twice its length when you wrap the cables.• Overlap the tape when you wrap the cables.7. Attach the camera by screwing the threaded mount into the standmounting hole.8. Mount the flexible stand firmly to the ceiling or wall with screw B (included).• Do not drive the screws into a soft material. Drive the screws into a secure area of thewall, such as a column, otherwise the camera may fall and be damaged.• Use screws that are suited for the type of material the camera is mounted to.• Be careful not to nip the cables.• Make sure the flexible stand is firmly mounted on a beam of wood (25 mm [1 inch] andgreater) etc. When there is no beam, apply a board on the other side of the ceiling or wallto make sure the camera does not drop.9. Adjust the camera position and tighten the flexible stand grip firmly.• Confirm that the cords have been waterproofed and that the portion of the cord protrudingfrom the flexible stand is wrapped in self bonding tape, as shown in (A) below.10. Secure the safety wire to the ceiling or wall using screw B (included) andwasher L (included).• Leave some slack in the safety wire, as shown.• Make sure the safety wire is firmly mounted on a beam of wood (25 mm [1 inch] andgreater) etc. When there is no beam, apply a board on the other side of the ceiling or wallto make sure the camera does not drop.• Make sure to waterproof the opening of the duct so that water does not enter it.• Attach the safety wire in a position so that if the camera were to become detached, itwould not fall on nearby people.For BB-HCM715 (INDOOR USE ONLY): Wiring through a hole made in theceiling or wallMake a hole for cables in the ceiling or wall. Secure the safety wire to thecamera and pass the cables through the notch. Then follow steps 7, 8, 9 and 10.When mounting on a mortar or concrete surface• Prepare anchors for 4 mm (3/16 inch) diameter screws for mounting.1. Place the flexible stand on the ceiling or wall where you plan to mount theflexible stand and mark the points where you are going to make holes.2. Make holes with an electric drill. Insert anchors (customer-provided) intothe holes and push them inside the holes with a hammer.• Mortar ceilings or walls break easily when drilling. Be careful of pieces of mortar whichmay become loose and fall.3. Mount the flexible stand using the screws.Flexible Stand Mount Tripod Mount1. Screw the threaded mount intothe stand/tripod mounting hole.2. Turn the grip firmly.Tripod(customer-provided)Stand/tripodmounting holeStand/tripodmounting holeFlexiblestandThreadedmountGripSafety wireWasher SScrew A12Screw holeScrew AConnector coverHook for AC adaptor cord,video cable, external I/Ointerface wiresHook for externalaudio cables34Sunshade Screw ADo not coverthe ventilation hole.N Ceiling N WallN Ceiling N WallN Ceiling N WallN Ceiling N WallN Ceiling N WallIndicatorStand/tripodmountingholeThreaded mountAt least 25 mm(1 inch)Screw BAt least 25 mm(1 inch)Grip(A)Grip (A)Duct(customer-provided)Screw B Washer LDuct(customer-provided)Washer LScrew BScrew BHole for cablesφ 25 mm(φ 1 inch) Screw BHole for cablesφ 25 mm(φ 1 inch)Drill for concrete (in case of tile, use a drill for tile)StandmountingholeThreadedmountScrew B

/ 4

Related manuals for Panasonic BB-HCM715