|
10Part Names and Functions button Switches to the source selector buttons for the utility 1 bus/utility 2 bus that can be inserted to background wipe bordersand key edges. button Switches to the start button to play back the macro memory assigned to the KEY bus crosspoint buttons. Theassignment can be made from the button on the top menu → [MACRO] → [XPT Assign] tab. to buttonsSwitches to the source selector buttons for the DSK fill buses or DSK source buses.f If you select key fill signal or key source signal using the KEY bus crosspoint buttons, the signals are linked andanother signal is automatically selected. The unit’s linking operation has two modes. The mode setting can be madefrom the button on the top menu → [SOURCE LINK] → [Key Assign] tab → [Master/Slave].2 KEY bus crosspoint buttons (1 to 16)Selects the source of the bus which was selected by the KEY bus selector buttons.Source can be selected using the <2nd PAGE>/<3rd PAGE> button. (Maximum of 64) (page 10)3 Source name display panelsDisplays applications of the crosspoint buttons. The display settings of the source name display panels can be made from the button on thetop menu → [SOURCE NAME] → [Panel Name] tab.When operating other than macro bus: “crosspoint number” on the upper line, “input source name” on the lower lineWhen operating macro bus: “macro name” on the upper line, “input source name” on the lower line4 PGM/A bus crosspoint buttons (1 to 16), PST/B bus crosspoint buttons (1 to 16)Selects the video signals of the PGM/A bus and PST/B bus.Source can be selected using the <2nd PAGE>/<3rd PAGE> button. (Maximum of 64) (page 10)f Bus mode can be selected from the button on the top menu → [OPERATE] → [Transition] tab → [Bus Mode] column → [Bus Mode].5 buttonPress the to / to /// to buttons while holdingdown the button to switch the bus selection applications. For the to buttons, the bus selection applicationscan be switched even when the selected button is pressed again.Example) buttonWhen only the button is pressed, the KEY bus crosspoint buttons are switched to the source selector buttons of the KEY1 fill bus.When the button is pressed while the button is held down, the KEY bus crosspoint buttons are switched to the sourceselector buttons of the KEY1 source bus.6 <2nd PAGE>/<3rd PAGE> buttonsSwitch the page to select the source with the KEY bus crosspoint buttons, PGM/A bus crosspoint buttons, or PST/B bus crosspoint buttons.f The pages of the buses included in the corresponding ME can be switched at once. To switch pages at individual buses, assign the <2ndPAGE>/<3rd PAGE> button to the KEY bus crosspoint buttons, PGM/A bus crosspoint buttons, and the PST/B bus crosspoint buttons.Button status Displayed page<2nd PAGE> button <3rd PAGE> buttonOff Off First pageLit Off Second pageOff Lit Third pageLit Lit Fourth page7 buttonEnables/disables image effects (paint, mono colors, mosaics, defocusing, etc.) to be added to images selected at the PGM/A bus and PST/B bus.f The setting to enable/disable image effects to be added to images selected in the KEY bus can be made from the / button on the topmenu → [IMAGE] → [Key1]/[Key2] tab → [Mosaic/Defocus] column.8 Bus tallyIndicates the output status of the buses. The buses that comprise the on-air tallies will light up.Multi-selection panel areaRECALLSTOREDEL4-1 4-34-24-4 4-64-54-7 4-94-8OPSTILL1121 Mode selection buttonSwitches functions that can be operated on the multi-selection panel. button Selects background wipe preset. button Registers/recalls/deletes register memories of the shot memory. buttonRecalls register memories of the event memory. This button is also used to select register memories during EMEM-LINKtransition.f Registration/editing are performed using the menu.
|
