OneStart

Menu

Octel Aria 1.2 Release Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Contents
  1. Edition
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Features for Service Personnel
  7. Features Administered by System Managers
  8. Compatibilities With Applications
  9. Multiline Networking
  10. ASCII Name Verification
  11. Control of MWI
  12. TDD/TTY Support
  13. Application Easy Access
  14. Node Expansion
  15. Overview
  16. Check The Major Steps
  17. Make Sure that the Correct Equipment is Available
  18. Software
  19. Verify the System Boot Area
  20. Connect the PC and the Server
  21. PC-to-Octel Overture 350 Direct Connection
  22. Connecting the PC remotely to the server
  23. Install the Online Upgrade Tool on the PC Hard Drive
  24. PC's ONLINE UPGRADE Installation Program Screen
  25. Verify the Values in the PC Setup Menu
  26. Load Software and Phrase Diskettes on the PC Hard Drive
  27. Copy/Delete UPG Menu
  28. Verification Prompt
  29. Status Messages Screen With File Copy Complete Message
  30. Perform the Automatic Upgrade
  31. Modem Setup Menu
  32. Example of Status Messages Box With Confirmation Prompt
  33. Verify the Upgrade
  34. Reset the Boot Area, and Boot the New Software
  35. Make Software and Phrase Areas Redundant
  37. FLT-A Card and its Removal and Replacement
  38. Example of Menu 13.11, Review Card Management
  39. Conversion of Branch, Aspen, or Maxum to Octel Overture 250 Using PC Tape
  40. Menu 20.1.5, Port Traffic Statistics Utility
  41. Mixed 1-GB, 2-GB, and 4-GB Message Drives, and the Upgrade Message Drive Utility
  42. Reset Mirrored Drive Status Utility
  43. Collapse Nodes Utility
  44. Example of the Node Collapsing Utility Screen
  45. Revised Enable Drive Utility
  46. Hot-Plug Replacement of Tape Drive in Octel Overture 250
  47. Hot-Plug Addition of a Second System Drive in Octel Overture 250
  48. Flash EPROMs on CCF Card
  49. New Error Messages for Tape Drive Operations
  50. PCR CORRECTIONS
Octel Aria 1.2 Release Manual Manual pdf 56 page image
System Utilities and Procedures 3-13101–1477–001 Edition 2When you press any key, the Drive Replacement Utilities menu reappears.On any Octel Overture 250 or 350 server with Aria 1.2, this prompt is not displayed, and theutility automatically disables and deinstalls the failing system drive, then proceeds with systemdrive replacement as it did for Aria 1.1.On a non-GMR Octel Overture 250 that has two system drives, the SMT prompts you totemporarily move the system drive being replaced to another slot so that the utility can try tocopy the messages on this system drive to the replacement drive. The copy might not succeed,depending on the failure mode of the original drive. If the failing system drive cannot be enabledin its new temporary slot, the ERROR – Failed spin control. Press any key to continue. promptappears. After you press any key, with Aria 1.2 the following new prompt appears:WARNING – Unable to spin up the original System Drive X in slot Y.If you continue all messages from the original System Drive X will be lost.y – Continue and install the new System Drive.n – Re-insert original System Drive into slot Y and try to spin up again.Continue? (y/n):If this prompt appears, you can reinsert the original system drive into its temporary slot, type N,and press Return to try to enable the original system drive. You can type Y and press Return toproceed with the installation of the new system drive; if you choose this option, the messages onthe original system drive are lost.(The Replace Message Drive utility is unchanged from Aria 1.1.)Hot-Plug Replacement of Tape Drive in OctelOverture 250Aria 1.1 supports an optional tape drive. After a tape drive is removed and reinstalled or replaced,the server must be rebooted for the drive to become active again.With Aria 1.2, you can physically install the tape drive in drive slot 6 in an Octel Overture 250while the server is running. The tape drive is available as soon as it is installed. Rebooting is notrequired as it was for Aria 1.1. This capability also applies to a hard-disk drive installed in slot 6.The tape drive’s red light remains on until the drive is accessed; this is not an error condition.When you install or replace a tape drive on an Octel Overture 250 that has Aria 1.2 software,use the Installing a Tape-Backup Drive on an Octel Overture 250 Installation Instructions,P/N 181–1173–001; do not shut down or power off the server.
/ 64
This manual is suitable for:
Aria 1.2
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved