NAPCO Gemini GEM-X255 Installation Instructions Manual

Also see for Gemini GEM-RP1CAe2: Installation instructions Installation instructions Installation instructions Installation instructions Operating guide

NAPCO Gemini GEM-X255 Installation Instructions Manual Manual pdf 23 page image

L NAPCO Security Systems X GEM-X255 Installation InstructionsWI1093C 3/04 !Page 23G0 will clear the entry at the cursor. When programming zone descriptions, buttons 3 and 6 will scrollnot only through numbers 0-9, but through the alphabet and a series of punctuation marks and symbols as well. (Roughly notethe order in which the letters, numbers and symbols are displayed so that you will be able to determine the proper direction toscroll, up or down, for fastest access. As familiarity improves, so will programming speed). When the description has been en-tered and is satisfactory as displayed (e.g. "GARAGE"), you MUST press the U or D button to save it in memory.To advance to the next zone (or to any other zone, for that matter), position the cursor over the displayed Zone Number, i.e., "01" using buttons 1 and 2. Change the Zone Number using buttons 3 and 6. Repeat the zone-description programming procedure for the new zone. Advance to the next zone and repeat until all zones (up to 96 zones)have been programmed (255 zones can be programmed in PCD-Windows Quickloader download software).ARMING AND DISARMING THE SYSTEMIn the normal disarmed state, only the green STATUS LED will be on and the display will read "SYSTEM READY". To silencean alarm, enter any User Code, then press the U or D button. Any valid User Code may be used to arm or disarm; an Arm-Only Code may only be used to arm.Arming!To arm, enter a valid User Code, then press the D button. (For all "Classic GEM-RP keypads)!To arm, enter a valid User Code, then press the Q button. (For all "K Series" keypads)(If a wrong code is entered, the keypad will display "INVALID ENTRY / TRY AGAIN"). The green STATUS LED will go off,the red ARMED LED will go on, and the display will read "PLEASE EXIT IN / XXX SECONDS" ("XXX" representing the pro-grammed exit-delay time, in seconds). The exit delay will immediately start counting down toward "000", in 10-second decre-ments, indicating the available time remaining to exit through an exit/entry door.1. If Exit Delay Restart is enabled, after the panel is armed and the exit door is opened and then closed, exit delay willrestart at 60 seconds. If re-entry occurs within this 60-second interval, the alarm device will sound a 2-second warning"chirp", if programmed, as an entry reminder to the user to return to the keypad and disarm.2. (GEM-RP1CAe2/GEM-K1CA keypads only). An "S" in the display (e.g. "EXIT TIME XXX S") will appear as a re-minder that the system is being armed with the Service Code active. (To turn off the Service Code, disarm, then rearmusing a regular Arm/Disarm Code).3. If a System Trouble is displayed, there should be an attempt to correct the system trouble (for example by calling analarm maintenance or an alarm repairman). If this cannot be done, then press the C button to allow 5 minutes toaccess the keypad without the system trouble display. Immediate attention should be provided, when system troublesare encountered.4. In commercial applications, if Start Exit Delay After Ringback is programmed, exit delay will not start until the centralstation acknowledges receipt by a ringback tone at the keypad. The display will read "PLEASE WAIT" while the controlpanel communicates to the central station. If the ringback tone does not sound within about 30 seconds, the STARTEXIT TIME function may be used to manually start exit delay.DisarmingWhen the exit time has elapsed, the display will read "SYSTEM ARMED". This indicates that upon entering the premisesthrough an exit/entry door, there will be an entry delay to allow time to disarm the panel. The GEM-RP1CAe2 or GEM-K1CAdisplay will read "DISARM NOW / XXX SECONDS" ("XXX" representing the programmed entry-delay time, in seconds). The sounder willcome on and the entry delay will immediately start counting down toward "000" in intervals of 10 seconds, indicating the avail-able time remaining to disarm the panel. (Note: The sounder will "pulse" with the GEM-X255 version 3 and above. Thesounder will sound a "steady" tone with the GEM-X255 version 1B and lower). The sounder will emit a rapid pulsing warningtone during the final 10 seconds.To disarm the panel, enter a valid User Code, then press the U or D button.Arming in AWAY MODEAWAY MODE provides for full protection of the perimeter and interior zones. Exit/Entry doors are provided with Exit/Entrydelays. A "Classic" (non "K Series") keypad (GEM-RP1CAe2) will display "SYSTEM ARMED", while a "K Series" keypad(GEM-K1CA) will display "ARMED AWAY." The RED LED will remain ON. With "K Series" keypads such as the GEM-K1CA,press Q to begin the exit delay process (the exit delay will immediately start counting down toward "000", in 10-seconddecrements, indicating the available time remaining to exit through an exit/entry door).BASIC OPERATION