NAPCO GEM-RP8LCD Installation Instructions Manual

Also see for GEM-RP8LCD: Operating guide Operating guide

Contents

NAPCO GEM-RP8LCD Installation Instructions Manual Manual pdf 6 page image

Page 6KEYPAD MESSAGESThe GEM-RP8-LCD Keypad can display the following messages. Note: Refer to OI276.ALARM - Alarm condition, followed by one or more zone descriptions.ALARM MEMORY - Appears after an alarm condition and a valid code is en-tered or when alarm condition times out. Warns of a past alarmcondition.BELL TEST - Appears after entering this Function Menu item that initiates belltest. Enter this command to turn on the Bell, keypad sounder andkeypad LEDs for 2 seconds.BYPASSED ZONES - Displays one or more zones bypassed.CAN'T ARM SYSTEM - Arming attempt made, but system condition preventsarming.CAN'T ARM SYSTEM...PRESS RESET - Displays when arming is attemptedwith the Fire icon on or system troubles displaying. Solution is topress the RESET button and then arm the system.CAN'T ARM SYSTEM...SILENCING - Displays when the bell is on and a validcode is entered.CAN'T ARM SYSTEM...ZONE FAULTED - Displays when arming is at-tempted with a Zone in trouble. Secure zone (or bypass) beforearming.DEALER PROGRAM MODE - Appears after entering a valid Dealer Code andentering Dealer Program Mode.DIRECTORY - Displays a list of all zone descriptions.DISARM NOW XXX SECONDS - Entry delay in progress. XXX = Entry timeremaining in 2-second decrements.ENTER CODE FOR PROGRAM MODE - Appears after Function Menu itemis selected to Activate Program Mode. Enter your code then pressENTER to enter Program Mode.ENTER CODE FOR USER x - Enter the number of the user to be added orchanged, enter the 4 digit code.ENTER DEALER CODE TO EXIT - In Dealer Program Mode, appears afterpressing [Function] [8]. You must enter the Dealer code to leaveDealer Program Mode.ENTER LOCATION < > - In Dealer Program Mode, enter a 2-digit locationnumber (see programming sheet).FAULTED ZONES - One or more zones not secured. Status of zone descrip-tion(s) displayed.FIRE ALARM - Alarm condition on a Fire Zone. Enter your code then pressENTER to silence the sounder.FORCED RESET - Appears when pressing [1] [2] and [3] simultaneously.INVALID ENTRY TRY AGAIN - Wrong code entered.LCD TO LCD TRANSFER OPTION - Zone descriptions and other keypadconfiguration information can be transferred from the programmedkeypad (Sending) to the unprogrammed others (Receiving) in thesystem.NONE - May appear if message "ZONE FAULTED" displays--but the zoneclears after entering the Function Menu.OUT OF SYSTEM - Appears about 30 seconds after disconnecting (or short-ing to ground) the green data wire. Also appears after disconnectingthe data wire and pressing RESET. This message must display inorder to access Keypad Configuration Mode.PLEASE EXIT XXX SECONDS - Displays exit delay time in 2-second decre-ments.READY TO ARM - All zones operating; system can be armed. ("SYSTEMREADY" is an alternate equivalent message).RECEIVING - Appears while receiving Keypad Configuration or Zone Descrip-tions from a Quickloader or another RP8LCD keypad that is sendingdata.RP CONFIGURATION MODE - You are entering the RP8LCD Configurationmode. Changes in this mode are stored in the keypad.RP VERSION - Software version appears when entering Keypad Configura-tion Mode.SENDING - Appears while sending Zone Descriptions to another RP8LCDSENDING STOPPED - PLEASE WAIT - When large amounts of data aretransferred, pauses may appear for a few seconds, accompanied bythis message.SYSTEM ARMED - Panel armed.SYSTEM READY - All zones operating; system can be armed. ("READY TOARM" is an alternate equivalent message).-->TO START PRESS THE ENTER KEY - Initiate the LCD to LCD TransferOption by pressing Enter on the keypad.USER PROG. MODE USERS = 12345678 - Enter the number of the user tobe added or changed and enter the 4-digit code.ZN DESCRIPTIONS MODE - You are entering the Zone Descriptions Modewhich allows you to change and update the zone descriptions whichappear on the keypad display to suit the particular design of theprotected premisesZONE FAULTED - One or more zones not secured.System TroublesAC Failure - Power failure. Check power transformer. Check for blown fuseor circuit breaker; general power outage.Bell Wire Cut - Bell wire severed (open on bell circuit).Fail to Comm - Unsuccessful communication to central station. Note: Willalso display if panel is improperly programmed to report: i.e., Re-port Alarm, Report Codes, Subscriber ID Numbers, etc. Must beprogrammed.Telco Line Cut - Telephone line cut or system down.Low Battery - Battery below 11 volts. If not recharged within 48 hours afterAC is restored, replace battery.Rcvr or Ezm Tbl - EZM module cover removed, or keypad EZM not respond-ing, or receiver not responding.RF Receiver Jam - Receiver not responding/jammed.RF LB / ZnXX - Burglar Transmitter Low Battery. XX = The zone number towhich the transmitter is mapped. Replace Battery.RF SUP ZnXX - Supervisory Burglar Transmitter Indication--panel has notreceived a signal from the transmitter within 12 (default) hours orprogrammed time. XX = The Zone number to which the transmitteris mapped. Replace Battery.RF Smk LB #XX - Smoke Detector Low Battery. XX = The smoke detectornumber as programmed in the panel. Replace Battery.RF Smk SUP #XX - Supervisory Smoke Detector Indication. Panel has notreceived a response from the transmitter within 4 (default) hours orprogrammed time. XX = The smoke detector number as pro-grammed in the panel. Replace Battery.Fire Trouble - Appears when an open in the hard-wired smoke detector exists.Zn Trouble #XX - Appears when a zone trouble exists. The panel has one ormore of the following 3 troubles: Zone Short (P800 panels only),Transmitter Tamper or Dual Tech Self Test Fail. XX = The Zonenumber.

/ 8

Related manuals for NAPCO GEM-RP8LCD