Mitsubishi Electric FX3S-10M series Hardware Manual

Also see for FX3S-10M series: User manual Beginners manual Structured programming manual User manual User manual

FX3S SERIES PROGRAMMABLECONTROLLERSHARDWARE MANUALThis manual describes the part names, dimensions, mounting, cabling andspecifications for the product. This manual is extracted from FX 3S Series User'sManual - Hardware Edition. Refer to FX3S Series User's Manual - HardwareEdition for more details. Before use, read this manual and manuals of relevantproducts fully to acquire proficiency in the handling and operating the product.Make sure to learn all the product information, safety information, andprecautions.And, store this manual in a safe place so that you can take it out and read itwhenever necessary. Always forward it to the end user.Registration: Phillips is a registered trademark of Phillips Screw Company.The company name and the product name to be described in this manual arethe registered trademarks or trademarks of each company.Effective December 2017Specifications are subject to change without notice.© 2013 MITSUBISHI ELECTRIC CORPORATIONSafety Precaution (Read these precautions before use.)If the equipment is used in a manner not specified by the manufacturer, theprotection provided by the equipment may be impaired.This manual classifies the safety precautions into two categories:and .Depending on the circumstances, procedures indicated by mayalso cause severe injury.It is important to follow all precautions for personal safety.Associated manualsAssociated manualsFX3S Series PLC (main unit) comes with this document (hardware manual).For a detailed explanation of the FX3S Series hardware and information oninstructions for PLC programming, refer to the relevant documents.Manual Number JY997D48301Revision GDate December 2017Indicates that incorrect handling may cause hazardousconditions, resulting in death or severe injury.Indicates that incorrect handling may cause hazardousconditions, resulting in medium or slight personal injuryor physical damage.STARTUP ANDMAINTENANCEPRECAUTIONS• Do not touch any terminal while the PLC's power is on.Doing so may cause electric shock or malfunctions.• Before cleaning or retightening terminals, cut off all phases of the powersupply externally.Failure to do so may cause electric shock.• Before modifying or disrupting the program in operation or running thePLC, carefully read through this manual and the associated manuals andensure the safety of the operation.An operation error may damage the machinery or cause accidents.STARTUP ANDMAINTENANCEPRECAUTIONS• Turn off the power to the PLC before attaching or detaching the memorycassette. If the memory cassette is attached or detached while the PLC'spower is on, the data in the memory may be destroyed, or the memorycassette may be damaged.• Do not disassemble or modify the PLC.Doing so may cause fire, equipment failures, or malfunctions.For repair, contact your local Mitsubishi Electric representative.• Turn off the power to the PLC before connecting or disconnecting anyconnection cable.Failure to do so may cause equipment failures or malfunctions.• Turn off the power to the PLC before attaching or detaching the followingdevices.Failure to do so may cause equipment failures or malfunctions.- Peripheral devices, display module, expansion boards, special adaptersand memory cassette• Do not use the chemicals for cleaning.• If there is the possibility of touching the PLC inside a control panel inmaintenance, make sure to discharge to avoid the influence of staticelectricity.DISPOSAL PRECAUTIONS• Please contact a certified electronic waste disposal company for theenvironmentally safe recycling and disposal of your device.TRANSPORTATION ANDSTORAGE PRECAUTIONS• The PLC is a precision instrument. During transportation, avoid impactslarger than those specified in section 2.1 by using dedicated packagingboxes and shock-absorbing palettes. Failure to do so may cause failuresin the PLC. After transportation, verify operation of the PLC and check fordamage of the mounting part, etc.How to obtain manualsFor the necessary product manuals or documents, consult with your localMitsubishi Electric representative.Manual name Manual No. DescriptionFX 3S SeriesUser's Manual- Hardware EditionJY997D48601MODEL CODE:09R535Explains FX3S Series PLCspecification details for I/O, wiring,installation, and maintenance.FX 3S/FX 3G/FX3GC /FX 3U/FX3UC SeriesProgramming Manual- Basic & AppliedInstruction EditionJY997D16601MODEL CODE:09R517Describes PLC programming forbasic/applied instructions STL/SFC programming and devices.MELSEC-Q/L/FStructuredProgramming Manual(Fundamentals)SH-080782MODEL CODE:13JW06Programming methods,specifications, functions, etc.required to create structuredprograms.FXCPU StructuredProgramming Manual[Device & Common]JY997D26001MODEL CODE:09R925Devices, parameters, etc.provided in structured projects ofGX Works2.FXCPU StructuredProgramming Manual[Basic & AppliedInstruction]JY997D34701MODEL CODE:09R926Sequence instructions providedin structured projects of GXWorks2.FXCPU StructuredProgramming Manual[Application Functions]JY997D34801MODEL CODE:09R927Application functions provided instructured projects of GX Works2.FX SeriesUser’s Manual- Data CommunicationEditionJY997D16901MODEL CODE:09R715Explains N:N link, parallel link,computer link, no protocolcommunication by RSinstructions/FX 2N-232IF.Certification of UL, cUL standardsPlease consult with Mitsubishi Electric for information on UL, cUL standardpractices and the corresponding types of equipment.Compliance with EC directive (CE Marking)This product complies with EC directive, however, this document does notguarantee that a mechanical system including this product will comply with ECdirective.Compliance to EMC directive and LVD directive of the entire mechanicalsystem should be checked by the user/manufacturer. For more details pleasecontact the local Mitsubishi Electric sales site.Caution for compliance with EC Directive• Please use the FX3S Series programmable controllers while installed inconductive shielded control panels under a general industrial environment.• Programmable controllers are open-type devices that must be installed andused within conductive control panels. Please secure the control panel lid tothe control panel (for conduction). Installation within a control panel greatlyaffects the safety of the system and aids in shielding noise from theprogrammable controller.• For the control panel, use the product having sufficient strength, fireprotectiveness and shielding property to an installation environment.• 24 V DC of the power supply must be supplied from the circuit double/reinforced insulated from the main power supply (MAINS).Caution for compliance with the LVD directive (EN61010-2-201:2013) *1• To an external connection port other than AC power supply terminal and ACinput/output terminal, connect the circuit separated from a dangerousvoltage by a double/reinforced insulation.• Between the commons having the adjacent relay output terminals, if anexternal power supply is higher than 120 V AC, the insulation is basic.Therefore, when using 120 V AC or higher external power supply and 30 VDC/AC or lower external power supply between the adjacent commons, donot handle 30 V DC/AC or lower external power supply as a touchable part,(When handling 30 V DC/AC or lower external power supply as a touchablepart, add a basic insulation.)• Do not wire two or more crimp terminals to one terminal. (If the wiring withtwo or more wires is needed, take an appropriate action such as adding anexternal terminal.)• For crimp terminals to be used for the wiring applied with 30 V AC or higher,use the products with insulating sleeves.• Cutoff device such as a breaker or a circuit protector should be installed inaccordance with the following precautions.- Use EN60947-1 or EN60947-3 standards.- Use CP30-BA 2P 1-MD 0.5A or the cutoff device having the cutoffperformance equivalent to CP30-BA 2P 1-MD 0.5A.- Place the cutoff device so that it can be operated easily.- Specify that the cutoff device is for this equipment.*1 For the time of compliance with the LVD directive (EN61010-2-201:2013),refer to FX 3S Series User's Manual - Hardware Edition.Incorporated ItemsCheck if the following product and items are included in the package:1. Outline1.1 Part namesWhen the top covers are openFX 3S/FX 3G/FX 3GC/FX 3U/FX 3UC SeriesUser's Manual- Analog Control EditionJY997D16701MODEL CODE:09R619Describes specifications foranalog control and programmingmethods for FX 3S/FX 3G/FX3GC/FX3U /FX3UC Series PLC.FX 3S/FX 3G/FX 3GC/FX 3U/FX 3UC SeriesUser's Manual- Positioning ControlEditionJY997D16801MODEL CODE:09R620Explains the specifications forpositioning control of FX3S /FX3G /FX3GC /FX 3U/FX 3UC Series andprogramming procedures.Included ItemsFX 3S-10MFX 3S-14MFX 3S-20MFX 3S-30MProduct 1 unitDust proof protection sheet 1 sheetManuals [Japanese/English] 1 manualManual name Manual No. DescriptionNo. Name[1] Top cover[2] Terminal namesshows a function grounding terminal.[3] Terminal block covers[4] Input display LEDs (red)[5] Peripheral device connecting connector cover[6]Operation status display LEDsPOW Green On while power is on the PLC.RUN Green On while the PLC is running.ERR Red Flashing when a program error occurs.Red Lights when a CPU error occurs.[7] Output display LEDs (red)[8] The year and month of production[9] Model name (abbreviation)[10] DIN rail mounting hooksNo. Name[1] Optional equipment connector[2] Power supply terminal, Input (X) terminals[3] Variable analog potentiometersUpper side: VR1, Lower side: VR2[4] RUN/STOP switch[5] Peripheral device connecting connector (USB)[6] Peripheral device connecting connector (RS-422)[7] Service power supply terminal (AC power type only),Output (Y) terminals[8] Terminal cover[9] Optional equipment connecting screw holes[1][2][3][4][5][6][7][8][9][10][1][8][9][3][4][2][5][6][8][7]SideBSideASideB JAPANESE ENGLISHJY997D48301G

/ 4

Related manuals for Mitsubishi Electric FX3S-10M series