Makita VR001G Instruction Manual

Also see for VR001G: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

7 ENGLISHIntended useThe tool is intended for removing bubbles from concretewhen casting concrete.NoiseThe typical A-weighted noise level determined accord-ing to EN60745-2-12:Model VR001GSound pressure level (LpA) : 80 dB(A)Uncertainty (K) : 3 dB(A)Model VR003GSound pressure level (L pA) : 80 dB(A)Uncertainty (K) : 3 dB(A)The noise level under working may exceed 80 dB (A).NOTE: The declared noise emission value(s) hasbeen measured in accordance with a standard testmethod and may be used for comparing one tool withanother.NOTE: The declared noise emission value(s)may also be used in a preliminary assessment ofexposure.WARNING: Wear ear protection.WARNING: The noise emission during actualuse of the power tool can differ from the declaredvalue(s) depending on the ways in which thetool is used especially what kind of workpiece isprocessed.WARNING: Be sure to identify safety mea-sures to protect the operator that are based on anestimation of exposure in the actual conditions ofuse (taking account of all parts of the operatingcycle such as the times when the tool is switchedoff and when it is running idle in addition to thetrigger time).VibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN60745-2-12:Model VR001GWork mode: load with flexible hoseVibration emission (a h) : 4.9 m/s2Uncertainty (K) : 1.5 m/s2Model VR003GWork mode: load with flexible hoseVibration emission (a h) : 4.9 m/s2Uncertainty (K) : 1.5 m/s2NOTE: The declared vibration total value(s) has beenmeasured in accordance with a standard test methodand may be used for comparing one tool with another.NOTE: The declared vibration total value(s) may alsobe used in a preliminary assessment of exposure.WARNING: The vibration emission during actualuse of the power tool can differ from the declared val-ue(s) depending on the ways in which the tool is usedespecially what kind of workpiece is processed.WARNING: Be sure to identify safety measuresto protect the operator that are based on an estima-tion of exposure in the actual conditions of use (tak-ing account of all parts of the operating cycle suchas the times when the tool is switched off and whenit is running idle in addition to the trigger time).EC Declaration of ConformityFor European countries onlyThe EC declaration of conformity is included as Annex Ato this instruction manual.SAFETY WARNINGSGeneral power tool safety warningsWARNING: Read all safety warnings, instruc-tions, illustrations and specifications providedwith this power tool. Failure to follow all instructionslisted below may result in electric shock, fire and/orserious injury.Save all warnings and instruc-tions for future reference.The term "power tool" in the warnings refers to yourmains-operated (corded) power tool or battery-operated(cordless) power tool.Cordless concrete vibrator safetywarnings1. Always keep your hands and face away fromvibrating head when operating.2. Switch off the tool immediately if you notice abnor-mal noise or something faulty during operation.3. Inspect the tool carefully for breakage, cracksor deformation if you accidentally drop it orstrike it against something.4. Do not carry the tool with finger on switch.5. Do not set the tool down and switch it on. Thevibrating head may whip around out of controland cause an accident.6. Be careful not to allow water, wet concrete orthe like to get into the tool. Do not let the toolfall into wet concrete.7. Insert the vibrating head carefully betweeniron/steel frames or reinforcing rods not tocome in contact with them.8. Do not crush or twist the flexible hose.9. Do not overly bend the flexible hose.10. Use a wet cloth or the like to carefully wipe offany wet concrete left on the tool after use. Extracare should be given to thorough cleaning ofthe vents, switch area, cover openings, etc.