Makita DFJ206 Instruction Manual

Also see for DFJ206: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

4 ENGLISHImportant safety instructions forbattery cartridge1. Before using battery cartridge, read all instruc-tions and cautionary markings on (1) batterycharger, (2) battery, and (3) product usingbattery.2. Do not disassemble battery cartridge.3. If operating time has become excessivelyshorter, stop operating immediately. It mayresult in a risk of overheating, possible burnsand even an explosion.4. If electrolyte gets into your eyes, rinse themout with clear water and seek medical atten-tion right away. It may result in loss of youreyesight.5. Do not short the battery cartridge:(1) Do not touch the terminals with any con-ductive material.(2) Avoid storing battery cartridge in a con-tainer with other metal objects such asnails, coins, etc.(3) Do not expose battery cartridge to wateror rain.A battery short can cause a large currentflow, overheating, possible burns and even abreakdown.6. Do not store the tool and battery cartridge inlocations where the temperature may reach orexceed 50 °C (122 °F).7. Do not incinerate the battery cartridge even ifit is severely damaged or is completely wornout. The battery cartridge can explode in a fire.8. Be careful not to drop or strike battery.9. Do not use a damaged battery.10. The contained lithium-ion batteries are subjectto the Dangerous Goods Legislation require-ments.For commercial transports e.g. by third parties,forwarding agents, special requirement on pack-aging and labeling must be observed.For preparation of the item being shipped, consult-ing an expert for hazardous material is required.Please also observe possibly more detailednational regulations.Tape or mask off open contacts and pack up thebattery in such a manner that it cannot movearound in the packaging.11. Follow your local regulations relating to dis-posal of battery.SAVE THESE INSTRUCTIONS.CAUTION: Only use genuine Makita batteries.Use of non-genuine Makita batteries, or batteries thathave been altered, may result in the battery burstingcausing fires, personal injury and damage. It willalso void the Makita warranty for the Makita tool andcharger.Tips for maintaining maximumbattery life1. Charge the battery cartridge before completelydischarged. Always stop tool operation andcharge the battery cartridge when you noticeless tool power.2. Never recharge a fully charged battery car-tridge. Overcharging shortens the batteryservice life.3. Charge the battery cartridge with room tem-perature at 10 °C - 40 °C (50 °F - 104 °F). Leta hot battery cartridge cool down beforecharging it.4. Charge the battery cartridge if you do not useit for a long period (more than six months).FCC cautionFor United StatesThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received,including interference that may cause undesiredoperation.Changes or modifications not expressly approved bythe party responsible for compliance could void theuser’s authority to operate the equipment.Note: This equipment has been tested and foundto comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection againstharmful interference in a residential installation. Thisequipment generates, uses and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmfulinterference to radio or television reception, which canbe determined by turning the equipment off and on, theuser is encouraged to try to correct the interference byone or more of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipmentand receiver.— Connect the equipment into an outlet on a cir-cuit different from that to which the receiver isconnected.— Consult the dealer or an experienced radio/TVtechnician for help.ICES-003 standardCAN ICES-3(B)/NMB-3(B)