OneStart

Menu

Kabola B-8 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Contents
  1. Preface
  2. Table Of Contents
  3. general introduction
  4. general safety
  5. fitting the boiler
  6. Connection of the Central heating system
  7. electrical installation
  8. Filling the central heating system
  9. mounting the burner
  10. Connecting the oil filter and oil burner
  11. operating the boiler
  12. Cleaning and maintenance
  13. Appendix A Technical specifications
  14. Appendix B Parts
  15. Appendix C Electrical diagram B8-B70 230V
  16. Appendix D Electrical diagram B80-B100 230V
  17. Appendix E Electrical diagram B8-B45 24V
  18. Appendix F Troubleshooting
  19. Appendix G CE-declaration
Kabola B-8 User Manual Manual pdf 9 page image
User manual Kabola B-serie, 1-4-2005 9Figure 7Figure 64. Connect point 2 of the connector to point L1 of the room thermostat.Attention: The core diameter of the connections mentioned above must be between 1 and 1,5mm².The wires should be suitable for the voltage used.Connecting the circulation pump (see figure 5 and electrical scheme in appendix C)1. Connect the pump to points 3 and 4 of the connector.2. Connect point 5 to the ground connection on the pump3. Replace the cover of the main connector.Electrical installation 24 Volts DCWarning: Never change the + pole with – poleon the battery (See figure 6).1. The connection of the room thermostatis identical to the connection for the 230 Voltsversion. Use figure 6 instead of figure 5.2. Connect the circulation pump to points3 and 4 of the main connector.3. The core diameter of the wires to points5 and 6 of the connector should conform to thevalues intable 1.Table 1Distance to the battery Core diameter± 6 metres 6 mm²± 15 metres 10 mm²4.1.5 Filling the central heating systemThe pressure in the system should:• Never be lower than 0,5 bar cold;• Never be higher than 2,5 bar hot;Follow the procedure listed below for filling the CH-system (see figure 7)1. Switch off the boiler2. Turn the coupling nut below the pressure indicator to loosen it;3. Pull the hose connection a little downwards;4. Connect the hose with a hose clamp to the connection.5. Fill the system slowly with water, until the pressure indicator indicatesa pressure of 2 bar.6. Fasten the coupling nut;7. Bleed the CH-system8. If necessary, fill with water again up to 2 bar of pressure.9. Switch on the boiler and let the pump run for about 5 minutes.10. Switch off the boiler.11. Check the water pressure, if it is too low, repeat steps 5 through to 10;12. Remove the hose.Hint: The CH-system can be filled with cooling fluid, suited for CH-systems (pH-value 8.5).
/ 20
Related manuals for Kabola B Series
Kabola HRE300 User Manual first page preview
Kabola HRE300 User Manual
Kabola HR Series User Manual first page preview
Kabola HR Series User Manual
This manual is suitable for:
B SeriesB-100B-12B-17B-25B-35B-45B-55B-70B-8B-80
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved