JVC HM-DH40000U Instructions Manual

Also see for HM-DH40000U: Supplementary guide Service manual

Contents

EN 398 Set recording speedPress REC SPEED to set the recording speed.9 Return to normal screenPress @ # to move the arrow to “CONFIRM”,then press OK.“PROGRAM COMPLETED PRESS [TIMER] TOENTER TIMER STANDBY MODE” appears on thescreen, then press OK to return to normal screen.0 Engage timer recording standby modePress TIMER (‰).The VCR turns off automatically and “‰” isdisplayed on the front display panel.To timer-record daily or weekly serialsPress DAILY (number “8”) or WEEKLY (number “9”)anytime during steps 4 through 8.“MON – FRI”, “MON – SAT”, “SUN – SAT” or“EVERY _ _ _” appears on the Program screen.● Pressing the button again makes the correspondingindication disappear.To use the VCR while it is in timer recording standbymodePress TIMER (‰) to cancel the timer recording standbymode, then press POWER to turn on the VCR.DO NOT forget to put the VCR into timer recordingstandby mode again by pressing TIMER (‰) after youuse the VCR; otherwise, you cannot record the broadcastyou want.● When “AUTO TIMER” ( pg. 57) is set to “ON”, thetimer recording standby mode is automaticallyengaged when the VCR is turned off. It is temporarilycanceled when the VCR is turned on. You do not haveto press TIMER (‰) to engage or disengage the timerrecording standby mode.ATTENTION FOR DBS RECEIVER USERSIf you are using a DBSreceiver (unless “INPUTCH” is set to “OFF” onDBS Receiver Set screen pg. 19), the bandindication (TV, CATV orDBS) appears under thechannel numberindication (SOURCE).TV :To timer-record a regular TV broadcastreceived on the VCR.CATV :To timer-record a cable TV broadcastreceived on the VCR, or through a cable box(unless “INPUT CH” is set to “OFF” onCable Set Up screen pg. 16).DBS :To timer-record a satellite broadcastreceived through a DBS receiver.NOTE:If “BAND” is set to “TV” on the Tuner Set Up Screen(pg. 14) and “INPUT CH” is set to “OFF” on Cable SetUp screen (pg. 16), “CATV” will not be displayed on theProgram screen; If “BAND” is set to “CATV” or “INPUTCH” is set to “ON” on Cable Set Up screen, “TV” will notbe displayed.If the channel number entered requires that the bandbe set, “7=DBS” is displayed on the screen.If this happens, press the Number key “7 (DBS)” toselect “DBS”.NOTES:●Even if a power failure occurs, the VCR keeps your timerprograms. However, the clock time is lost if it lasts for morethan 10 minutes.As a result, when the power is supplied again to this VCRafter the power failure, the following will take place.1. This VCR starts Auto Clock Set automatically to restore theclock time.2. If the clock time is restored correctly and “AUTO TIMER” isset to “ON”, each timer program you have made will startat its start time unless its end time has elapsed.●Programs that start after midnight must have the next day’sdate.●After timer recording is completed, the VCR turns offautomatically.●You can program the timer recording while a regularrecording is in progress; the menu screens will not berecorded.●If the tape reaches its end during timer recording, “‰”, “ ”,and “ #” blink.●To timer-record cable or satellite channels, be sure to keepthe cable box or DBS receiver turned on.CONFIRM CANCEL10:00 PMSTD (SP)110 CHDBS8:00 PMSTART TIME STOP TIME DATEDAILY/WEEKLYCHSOURCETIMER PROGRAMREC SPEEDSET PROGRAM WITH [+/–, REC SPEED,7=DBS,8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"START STOP DATE CHEXITPROG.12/24/03 (WED)EVERY WED