JVC HM-DH40000U Instructions Manual

Also see for HM-DH40000U: Supplementary guide Service manual

Contents

EN 354 Input receiving channel numberThe guide channelnumber, which isassigned to the TV orcable station for thePlusCode numberthat you entered instep 3, will appearautomatically on theGuide Channel Set Up screen.Press @ # to input the number of the channel onwhich the broadcast for the PlusCode number isreceived on the VCR or cable box, then pressOK.● The Guide Channel Set screen appears onlywhen you input the PlusCode number of astation for which the guide channel number hasnot been set previously.● If you receive your channels with a cable boxand if you have properly set your Controller,“CABLE CH” appears in place of “VCR CH”. Ifnot, refer to pages 15 – 17.In that case, it is possible to change the channelby 10 channels by pressing and holding @ #.5 Check program dataThe PlusCodenumber you enteredand thecorresponding timerrecording program isdisplayed on theProgram screen.Check to make sure itis accurate.● To change the start/stop time, date or channelsetting, press the corresponding buttons tochange the settings; START +/–, STOP +/–,DATE +/–, TV/VCR CH +/–.● To timer-record daily or weekly serials, pressDAILY (number “8”) or WEEKLY (number “9”).“MON – FRI”, “MON – SAT”, “SUN – SAT” or“EVERY _ _ _” appears on the Program screen.Pressing the button again makes eachcorresponding display disappear.● For the “SOURCE” setting, refer to page 39.● If you made a mistake, press BACK to accessthe VCR Plus+ screen again and input thecorrect PlusCode number.6 Set recording speedPress REC SPEED to set the recording speed.IMPORTANTIf you have moved to a different area or if a broadcastingstation’s channel number has been changed, the wrongVCR CH or CABLE CH number will be displayed on theProgram screen in step 5. When this happens, set thecorrect guide channel number for that station. ( pg. 36,“Changing VCR Plus+ Setting”)NOTES:●Even if a power failure occurs, the VCR keeps your timerprograms. However, the clock time is lost if it lasts for morethan 10 minutes.As a result, when the power is supplied again to this VCRafter the power failure, the following will take place.1. This VCR starts Auto Clock Set automatically to restore theclock time.2. If the clock time is restored correctly and “AUTO TIMER” isset to “ON”, each timer program you have made will startat its start time unless its end time has elapsed.●If the tape reaches its end during timer recording, “‰”, “ ”,and “ #” blink.●To timer-record cable channels received through a cable box,be sure to keep the cable box turned on.7 Return to normal screenPress @ # to move the arrow to “CONFIRM”,then press OK.“PROGRAM COMPLETED PRESS [TIMER] TOENTER TIMER STANDBY MODE” appears on thescreen, then press OK to return to normal screen.8 Engage timer recording standby modePress TIMER (‰).The VCR turns off automatically and “‰” isdisplayed on the front display panel.To use the VCR while it is in timer recording standbymodePress TIMER (‰) to cancel the timer recording standbymode, then press POWER to turn on the VCR.DO NOT forget to put the VCR into timer recording standbymode again by pressing TIMER (‰) after you use the VCR;otherwise, you cannot record the broadcasts you want.● When “AUTO TIMER” ( pg. 57) is set to “ON”, thetimer recording standby mode is automaticallyengaged when the VCR is turned off. It is temporarilycanceled when the VCR is turned on. You do not haveto press TIMER (‰) to engage or disengage the timerrecording standby mode.THEN PRESS [OK]GUIDE CH 12VCR CH – –SELECT WITH ARROW KEYSSELECTOKEXITMENUFUNCTION SET UP INITIAL SET UPTUNER SET UPCLOCK SET GUIDE CHANNEL OTHERCONFIRM CANCEL10:00 PMSTD (SP)12/24/03 (WED) 12 CHCATVEVERY WED8:00 PMSTART TIMEPLUSCODE NO. 12345STOP TIME DATEREC SPEED DAILY/WEEKLYCHSOURCESET PROGRAM WITH [+/–, REC SPEED,8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"START STOP DATE CHEXITPROG.TIMER PROGRAM